UK product. What is bolt size for driver side wing mirror?

Please note this is just a guide.
Door mirrors are usually bolted on from the inside. Open the door wide and look at the inside trim where the mirror is fasted to the door. The trim will be clipped on so CAREFULLY lever it off. This should expose the mounting bolts for the wing mirror. Usually 3 or 4.

Unclip your inside trim right behind the mirror mounting. You should be able to find the screws attaching the mirror.

Instructions
1


Disconnect your negative battery cable, if your Ford Focus has power side mirrors. If it has manual side mirrors, disconnecting the battery is unnecessary.

2


Pry off the wing mirror's inside sail panel (shaped like a triangle). Insert a trim panel tool between the door skin and the plastic panel to pry it off.





3


Carefully pull the sail panel away, minding the wiring if the mirror is power-operated. Unplug the electrical harness and set the panel aside.

4


Open the door and hold the outside part of the wing mirror steady. Remove the mounting bolt with a socket wrench, and then remove the mirror screw with a Phillips screwdriver (the mirror bolt and screw is visible with the panel removed).

5


Pull the wing mirror assembly from its mount (from the outside). Insert the replacement mirror assembly in place; tighten the bolt and the screw.

6


Attach the wiring connection to the replacement mirror. Position the sail panel in place and push it against the door to snap it back on.

Check this guide as reference for solve ypur problem; this is one DIY about replace Wing Mirror...
1.- Disconnect your negative battery cable, if your Ford Focus has power side mirrors. If it has manual side mirrors, disconnecting the battery is unnecessary.
2.- Pry off the wing mirror's inside sail panel (shaped like a triangle). Insert a trim panel tool between the door skin and the plastic panel to pry it off.
3.- Carefully pull the sail panel away, minding the wiring if the mirror is power-operated. Unplug the electrical harness and set the panel aside.
4.- Open the door and hold the outside part of the wing mirror steady. Remove the mounting bolt with a socket wrench, and then remove the mirror screw with a Phillips screwdriver (the mirror bolt and screw is visible with the panel removed).
5.- Pull the wing mirror assembly from its mount (from the outside). Insert the replacement mirror assembly in place; tighten the bolt and the screw.
6.- Attach the wiring connection to the replacement mirror. Position the sail panel in place and push it against the door to snap it back on.

Hope helps (remember comment and rated this). TY for using Fixya.

Hello Darren, there is not special tools required.Just open the plastic cover from inside/against the mirror and you will see 2 or 3 bolts with 5 mm Allan key head.Good luck

hi from uk if the headlight assy is anything like some here in uk ie ford focus ? you may find there is a 3rd bolt tucked away out of sight this is probably located as on focus ? if you feel or use amirros? and look/feel on the inner wing between h/lamp and inner wing you may find a small bracket that is attached to inner wing ? and another on the lamp assy these 2 brackets are locked together with a 10 mm spanner/socket bolt approx 6 ba threaded unfasten and remove bolt the lamp will probably come out best to use 3/8 or 1/4 " drive socket+extention ?

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can remove the bolts securing the mirror to the door.

Hello Joe

Yes you have an E46, You need to order the UK drivers side glass and make sure you specify it's a coupe. the saloons have a different wing mirror.

Hope this helps, please don't forget to rate me.

1. Disconnect the negative battery cable.
2. Remove the outside rearview mirror garnish.
3. Disconnect the harness connector.
4. Remove the 3 bolts and the outside mirror.

To install:

1. Install the outside mirror and tighten the bolts to 60 inch lbs. (7 Nm).
2. Connect the wiring harness.
3. Install the mirror garnish.
4. Connect the negative battery cable

There is a black plastic cover on the other side of the mirror, take it off make sure you have the wires long enough to splice back to you will be able to see all the bolts that need to come off to replace the mirror. You will be able to figure out the rest it is very simple