What are the cylinder head torque settings for a KIA K2700
www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...
SOURCE: what are the torque specs for the head bolts for a 1999 sportage
hi bob
head torque on the 2.0 DOHC is 64 ft lbs , done in two -three steps , also there is a sequence for proper order . here is a very good description with graphics .
1999 kia sportage 2.0 DOHC head torque
Thanks for using FIX YA !
J5
SOURCE: head bolts torque settings
According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.
SOURCE: head bolts torque settings for dogde neon 2002
assuming this is the "C" engine 8th digit on VIN plate. Use new bolts. torque first step to 25lbs, 2nd 50lbs, then 3rd 50lbs, then 1/4 turn.
SOURCE: head bolt settings
1st - step; - 22 ft./lbs. 2nd - step; - 58 ft./lbs. 3rd - step, loosen all bolts completely; 4th - step; - 22 ft./lbs. 5th - step; - 54 ft./lbs.
SOURCE: please timing belt marking diagram
Also check this diagram too:---
Part names:--
1. CYLINDER HEAD .
2. HEAD GASKET .
3. VALVE COVER .
4. VALVE COVER GASKET .
5. VALVE GUIDE .
6. INTAKE VALVE .
7. EXHAUST VALVE .
8. VALVE SEALS .
9. VALVE SPRINGS .
10. VALVE SPRING RETAINERS .
11. VALVE SPRING SEATS .
12. VALVE KEEPER .
13. ROCKER ARMS .
14. ADJUSTER .
15. EXHAUST CAMSHAFT .
16. INTAKE CAMSHAFT .
17. CAMSHAFT SEAL .
18. FRONT COVER .
19. FRONT COVER GASKET .
20. CAMSHAFT GEAR .
21. TIMING BELT .
22. IDLER PULLEY .
23. TENSIONER .
24. CRANKSHAFT GEAR .
25. PISTON .
26. CONNECTING ROD .
27. BEARING SET .
28. BEARING SET .
29. THRUST WASHER .
30. CRANKSHAFT .
31. REAR MAIN SEAL .
32. REAR MAIN SEAL RETAINER .
33. PULLEY .
34. OIL PAN .
35. BAFFLE PLATE .
36. OIL PUMP .
37. OIL PUMP GEAR .
38. REAR COVER.
39. OIL PICK-UP.
40. SEAL.
----------------------
Click this link directly:-------- For more help on routing the timing belt:---
http://technoanswers.blogspot.com/2011/01/kia-v6-timing-belt-routing-diagrams.html
------------
This should help.Thanks.Helpmech.
3,502 views
Usually answered in minutes!
×