Driver door controls only works drivers door only.other 3 door controls dont function at all seperately or from drivers switch

check harness for short between door and the switches

DR/LCK fuse 25 amp . located in the I/P block
Fuse Block - I/P
In the right front kick panel

Power Door Locks System Components
The power lock system consists of the following components:
• Body control module (BCM)
• Driver door lock cylinder switch
• Front passenger door lock cylinder switch
• Driver door lock switch
• Front passenger door lock switch
• Door lock actuators in each of the doors
• DR LK Fuse 20-amp
Door Lock System Controls
The Power Door Lock System is controlled by the body control module (BCM) and can be activated by any one of the following:
• A door lock switch lock or unlock actuation
• A door lock cylinder switch unlock actuation
• A keyless entry transmitter actuation
• An automatic door lock actuation (Personalization function)
• An automatic door unlock actuation (Personalization function)
Door Lock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the lock position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the lock position.
Driver Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the left front (LF) door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked separate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed).

Check for broke wires inside the boot from body to driver door , this is a common problem . If you don't find broke wire's , pull the door panel to get at driver door switch . Check for voltage an ground circuit .
Rendezvous Door Lock System Components
The power door lock system consists of the following components:
?€¢
Body control module (BCM)

?€¢
Driver door lock switch

?€¢
Front passenger door lock switch

?€¢
Door lock actuators in each of the doors

?€¢
Door lock system fuse into the BCM (BCM D 25A fuse)

Door Lock Operation
When the BCM detects a transition of either of the door lock switches to the LOCK position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the Lock position.
Driver Door Unlock Operation
When the BCM detects a transition of either of the door lock switches to the UNLOCK position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the LF door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the BCM detects a transition of either of the door lock switches to the UNLOCK position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the Unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked seperate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed). This video on testing computer controlled door locks on a Subaru , doesn't matter . test yours same way > The BCM controls your door locks .
Are all of the power door locks inoperative from both door lock switches?

Power Door Lock Operation
The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door, but the rear integration module (RIM), which is the master control for the door lock system, determines when the lock functions are permitted. The RIM receives and examines the requested lock function from the individual door modules, or from the remote function actuator (RFA) via the class 2 serial data circuit. The RIM also examines the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. If the RIM determines that a lock or unlock function is permitted, it sends a class 2 message back to the individual door modules commanding them to perform that Lock or Unlock function.
Power Door Lock Components
The power door lock system consists of the following components:
?€¢
Driver door lock switch

?€¢
Passenger front door lock switch

?€¢
LH rear door lock switch

?€¢
RH rear door lock switch

?€¢
LH middle door lock switch (w/ V4U)

?€¢
RH middle door lock switch (w/ V4U)

?€¢
Driver door switch assembly (DDSA)

?€¢
Driver door module (DDM)

?€¢
Passenger front door module (PDM)

?€¢
LH rear door module (LRDM)

?€¢
RH rear door module (RRDM)

?€¢
Left middle door module (LMDM) (w/ V4U)

?€¢
Right middle door module (RMDM) (w/ V4U)

?€¢
Driver door lock actuator

?€¢
Passenger front door lock actuator

?€¢
LH rear door lock actuator

?€¢
RH rear door lock actuator

?€¢
LH middle door lock actuator (w/V4U)

?€¢
RH middle door lock actuator (w/ V4U)

?€¢
Driver door cylinder unlock switch

?€¢
Rear integration module (RIM)

?€¢
DRVMDL fuse (10-amp)

?€¢
PASS MDL fuse (10-amp)

?€¢
RRDR MDL fuse (10-amp)

?€¢
Class 2 serial data link

the drivers door switch is the master switch i would take a test light and check to see if the drivers door swich is sending 12 volts to other doors when pushing down on other windows test with test light to see if any light up if you find one that lights up stop pressing switch and see if it goes out if it does the switch is ok if it does not then the drivers door master switch is probably your problem

CHECK FUSES FOR POWER WINDOW,CHECK FUSE FOR POWER MIRROR AND CHECK FUSE FOR POWER DOOR LOCK.IF FUSE OKAY DOOR CONTROL MODULE FAULTY ITSELF.

extended warranty will not cover the master switch on driver door. befor replaceing it take the door panel off and their is a set nut on the pottom of the switch that comes lose allowing the connect to disconect try just tightning down the nut in most cases this will fix it, all the outher switches are juamper switches that all runn off the driver door as the main.

check and see if the window lock is on or not, driver side window and sunroof will still function when window lock is activated however, the other windows will not work, even by the drivers control, it should be the button on the top right next to your power door lock switch,

ok the switch on the drivers side not working is the problem,its not allowing the cicuit to be completed.you may want to check the passenger side lock actuator.

the master control switch on the drivers door needs to be replaced and it will be fixed.