Question about 2005 Cadillac SRX

1 Answer

?Hi . I need help , can anyone tell me when is EBCM located in 2005 Cadillac SRX ?

I checked few websites and each one gives different ( wrong ) location for EBCM . Must be hidden because I can't see it when I pop the hood . Any help will be greatly appreciated .

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 3,218 Answers

#2 is the EBCM under the hood

?Hi . I need help , can anyone tell me when is EBC - need-help-anyone-tell-me-when-ebcm-cx3phjt3442rbswrkqtrkisf-4-0_0.gif

Posted on Aug 02, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of abs control module in 2002 buick lesabre


Electronic Brake Control Module Replacement

Removal Procedure



    Click to Enlarge
  1. Turn OFF the ignition.
  2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Remove the left front wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  4. Remove the left front wheelhouse extension. Refer to Fascia Extension Replacement - Front in Bumpers.
  5. Important The area around the electronic brake control module (EBCM) must be free from loose dirt to prevent contamination of disassembled ABS components.
  6. Thoroughly wash all contaminants from around the EBCM.
  7. Rotate the EBCM connector tab up to the unlocked position.
  8. Remove the EBCM connector position assurance (2) from the EBCM electrical connector (1).
  9. Caution! To prevent equipment damage, never connect or disconnect the wiring harness connection from the EBCM with the ignition switch in the ON position.
  10. Disconnect the EBCM electrical connector (1) from the EBCM (4).


  11. Click to Enlarge
  12. Disconnect the brake pressure modulator valve (BPMV) electrical connector (2) from the EBCM (3).


  13. Click to Enlarge
  14. Remove the 6 EBCM to BPMV screws (2).


  15. Click to Enlarge
  16. Clean the surface of the EBCM/BPMV assembly.
  17. Important The EBCM cannot be repaired. If faulty, the unit must be replaced.
  18. Separate the EBCM (2) from the BPMV (1).

The above procedure is removal. Usually the code won't tell you what to replace. I don't know what testing you have done? Just reading the code might not be enough? The main reason I posted is to give you the location of module. Proper diagnostics is up to you. I hate to see you replace something and it not fix the problem. This is just my opinion.

May 26, 2018 | Buick Cars & Trucks

1 Answer

Can leaky shocks on a 2006 Cadillac DTS cause the traction control light to come on


If the light is on there are DTC'S - diagnostic trouble code's stored in ABS - anti - lock brakes computer . Have codes checked first , something wrong with electrical part of antilock brakes , I know, what does ABS have to do with traction control ! traction control is a function of the ABS control module . Leaking shocks ? clarify , air shocks etc.... Before you start guessing , have it check for codes .
This vehicle is equipped with the TRW 440 V antilock braking system.
The vehicle is equipped with the following braking systems:
?€¢
Antilock Brake System (ABS)


?€¢
Engine Drag Control (EDC)


?€¢
Dynamic Rear Proportioning (DRP)


?€¢
Traction Control System (TCS)


?€¢
Vehicle Stability Enhancement System (VSES) (w/JL4)

The following components are involved in the operation of the above systems:
?€¢
Electronic brake control module (EBCM)--The EBCM controls the system functions and detects failures.


?€¢
Electronic brake control module (EBCM)--The EBCM controls the system functions and detects failures.


The EBCM contains the following components:


-
System relay--The system relay is energized when the ignition is ON and no ABS DTCs are present. It supplies battery positive voltage to the solenoid valves and pump motor.


-
Vent tube--The vent tube, located in the EBCM connector, is an opening to the internal cavity of the EBCM. It allows ventilation of the EBCM internals.


?€¢
Brake pressure modulator valve (BPMV)--The BPMV contains the hydraulic valves and pump motor that are controlled electrically by the EBCM. The BPMV uses a 4 circuit configuration with a diagonal split. The BPMV directs fluid from the reservoir of the master cylinder to the left front and right rear wheels and fluid from the other reservoir to the right front and left rear wheels. The diagonal circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other.


Important: There is a rubber isolator located under the BPMV and on the mounting studs. The rubber isolators protect the BPMV and the EBCM from vehicle vibrations.


?€¢
The BPMV contains the following components:


-
Pump motor


-
Inlet valves (one per wheel)


-
Outlet valves (one per wheel)


-
Master cylinder isolation valves (one per drive wheel)


-
Prime valves (one per drive wheel)


?€¢
Wheel speed sensors (WSS)--As the wheel spins, the wheel speed sensor produces an AC signal. The EBCM uses this AC signal to calculate wheel speed. The wheel speed sensors are replaceable only as part of the wheel hub and bearing assemblies.


?€¢
Traction control switch--The TCS is manually disabled or enabled using the traction control switch.


?€¢
Stoplamp switch--The EBCM uses the stoplamp switch as an indication that the brake pedal is applied.


?€¢
Lateral accelerometer sensor (w/JL4)--The EBCM uses the lateral accelerometer sensor as an indication of the lateral acceleration of the vehicle.


?€¢
Yaw rate sensor (w/JL4)--The EBCM uses the yaw rate sensor as an indication of the yaw rate of the vehicle.


?€¢
Steering wheel position sensor (SWPS) (w/JL4)--The EBCM uses the SWPS as an indication of the position and rotation of the steering wheel.


This systems are very complex , your best bet would be to take it to a qualified repair shop .

Oct 18, 2016 | Cadillac Cars & Trucks

1 Answer

Where is ABS fuse located?


In the under hood fuse/relay box.

ETC / ECM - 15amp

ABS - 60amp

SEO B2 30 amp

no B+ at any of these fuse's check Ignition 1 relay .


This vehicle is equipped with the Bosch 5.3 antilock braking system.



The vehicle is equipped with the following braking systems:







?€¢





Antilock Brake System (ABS)














?€¢





Dynamic Rear Proportioning (DRP)















?€¢





Traction Control System TC2 (w/NW9)








The following components are involved in the operation of the above systems:







?€¢





Electronic Brake Control Module (EBCM) - The EBCM controls the system functions and detects failures.

















The EBCM contains the following components:
















-





System Relay - The system relay is energized when the ignition is ON and no ABS DTCs are present. It supplies battery positive voltage to the solenoid valves and pump motor.
















-





Vent Tube - The vent tube, located in the EBCM connector, is an opening to the internal cavity of the EBCM. It allows ventilation of the EBCM internals.















?€¢





Brake Pressure Modulator Valve (BPMV) - The BPMV contains the hydraulic valves and pump motor that are controlled electrically by the EBCM. The vehicle is equipped with traction control The BPMV uses a 4 circuit configuration with a front/rear split. The BPMV directs fluid from the reservoir of the master cylinder to the front wheels and fluid from the other reservoir to the rear wheels. The circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other.







Oct 31, 2015 | 2003 Hummer H2

1 Answer

Where is the fuse located for the headlights on a 2009 Saturn Aura?


There are two fuse panels on the 2007, 2008, 2009 Saturn Aura. The first is under the hood. The second is in the trunk hidden behind a pop-out panel in the side trim on the driver's side. , I dont Know if the XR is different but there is a third on the passanger side on the lower portion of the instrument panel near the floor

Jul 27, 2015 | Saturn Cars & Trucks

2 Answers

Need to locate the EBCM on a 1996 tahoe


Your brake light switch circuit also goes through the BLINKER SWITCH. Did you check that? (Most common culprit in GM vehicles.)

May 13, 2015 | 1996 Chevrolet Tahoe

1 Answer

I can't open the hood on my 2008 dodge magnum. I pull the lever and you can hear it pop but hood doesn't pop up what should I do


Pop the hood then go too front of car and hit hood near front with your palm. Try two or three different locations

Nov 14, 2014 | 2008 Dodge Magnum

1 Answer

How to repair abs EBCM


EBCM relay is the actual fault code cause. EBCM stands for Electronic Brake Control Module. ECBM stands for Electronic Brake Control Module. It is the big part that the brake lines go into and back out of from the MasterCyl and to the Brakes. It is also the ABS motor all in one. The relay is under the hood at the Fuse/Relay center just inbetween the EBCM/ABS and AirIntake. Relays are big and square. The underside of the Fuse/Relay center cover has the ID and placement embossed into it of everything in the F/R center. Be sure to check the fuses first. The relay needs power to operate and the EBCM or ABS or Brake fuse will be the one for it. Good luck!

May 28, 2014 | 2000 Chevrolet Blazer

1 Answer

Location abs module ebcm


This is at the front left of your car. If you pop the hood, and look down kinda under the air filter box, you should see it. To work on/change it, I found it easiest to jack up the drivers side of the car, remove the drivers front wheel, then I think I took out the inner fender, or somehow I could see into the module. This gave me enough room to change it.

Apr 27, 2013 | 2002 Buick Regal

2 Answers

2005 Impala 3.8L LS with service traction light on dashboard


It's usually the sensor inside the wheel hub or the wiring harness to the brake controller. The service traction light will set a trouble code. If your mechanic is stumped, authorize him to call a GM tech support line. The call is $50, but the GM tech support can help him figure out what's wrong.

Jul 19, 2017 | 2005 Chevrolet Impala

1 Answer

Need fisical location of the ECBM on my 2005 safari cargo van


The EBCM (Electronic Brake Control Module) is mounted to the BPMV (Brake Pressure Modulator Valve) located at the left front (lower) engine compartment.

EBCM Removal & Installation Procedure
  1. Remove the Brake Pressure Modulator Valve (BPMV). Refer to the Hydraulic Control Unit (BPMV) procedure in this section.
  2. Remove the 4 T-25 Torx® bolts (1) from the EBCM (2). (click image for zoom)

    zjlimited_1548.jpg
    Fig. Bolts (1), EBCM (2), bracket (3), bolts (4) and BPMV (5) (click image for zoom)

  3. Disconnect the 2-way ABS pump motor connector.
    WARNING Do not use a tool to pry the EBCM or the BPMV. Excessive force will damage the EBCM.
  4. Remove the EBCM (2) from the BPMV (5). Removal may require a light amount of force.
    1. Do not reuse the EBCM mounting bolts. Always install new bolts.
  5. Clean the EBCM to BPMV mounting surfaces with a clean cloth.
To install:

WARNING Do not use RTV or any other type of sealant on the EBCM gasket or mating surfaces.
  1. Install EBCM (2) onto BPMV (5).
  2. Install the 4 EBCM bolts (1).
    1. Tighten the 4 bolts to 39 inch lbs. (5 Nm) in an X-pattern.
  3. Connect the 2-way ABS pump motor connector to the EBCM.
  4. Revise the tire calibration using the Scan Tool Tire Size Calibration function.
  5. Use the scan tool to check and clear DTC memory.

Hope this helps.

Jul 06, 2011 | 2000 GMC Safari

Not finding what you are looking for?
2005 Cadillac SRX Logo

Related Topics:

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...