Rear Washer won't spray

I'd have to pull a wiring diagram to say for sure, but it appears both the front and back wiper motors are part of the same "series" circuit, so if you disconnect one, the other will not work.

Plug the front motor back up really quick. If the rear wiper motor works, you've found the problem. Is there a particular reason why you disconnected the rear motor?

Rear Wiper/Washer System Components
The rear wiper/washer system consists of the following components:
• Rear wiper/washer switch
• Window wiper module-rear
• Window washer pump-rear
• RR WIPER 15A fuse
• RR WPRB 25A fuse
Rear Wiper/Washer System Operation
The rear wiper module controls rear wiper motor operation. Battery voltage supplied to the module is used to operate the wiper motor in all modes and to return the rear wiper arm to the park position after the ignition is turned off. Accessory voltage supplied to the rear wiper/washer switch is used to supply the rear window wiper and washer switch signal circuits. In wiper switch positions 1 and 2 the wiper switch signal circuit voltage level to the wiper motor module determines the wiper motor delay interval. The rear window washer pump supply voltage circuit is used to provide the operating voltage for the rear washer pump for as long as the rear washer switch is pressed. The rear window washer switch signal circuit is used as a wash signal to the rear wiper motor module to operate the wipers during the rear wash operation.


Did you replace the rear wiper module ?

The washer fuse should have power (battery voltage) while the ignition switch is in the RUN position. Verify both sides of the fuse have power. If the rear wash functions them it's not the fuse.

The switch signals the Body Control Module (BCM). The BCM energizes the front washer relay.

Input to BCM from switch is BCM connector C1,24 PK. Output from BCM to relay is connector C4 15 OG.

You need to verify continuity from the the switch to the BCM and from the BCM to the relay.

Comment below for further assistance.

Replacing parts just to replace them wont fix a bad wire or part. Better to use a voltmeter and ohn meter to check if your getting power to the wires. You may have a bad connection or bad switch on the column for the pumps. Without checking the circuits it will behard to tell what it is thats wrong. Find a wiring diagram and trace the wires and components.

There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Check if ther is power to the front wiper moter when its on if ther is power then replace the moter, if no power check wiring.

Sounds like one of your nozzles is clogged to me. Try this.....Get a spray can of air, like the computer air spray. Stick the long air can nozzle into the spray nozzle. Shoot some air back into the system and see if it frees your clog. When my fluid gets low, mine will get gunk in it and clog to the point of not spraying at all. Compressed air usually does the trick. If not, remove and clean or replace the nozzles.

I have the same problem with my 2000 chevy blazer as skornec had posted. I kinda already figured the hose or spray nozzle was plugged. But the problem with checking those items is that I don't know where the hose is located to the back wiper. And the only thing that could be I see that could be the spray nozzle doesn't even have holes that washer fluid could spray from. So basically I just would LOVE if someone could please inform this lame brain of where to find the spray nozzle on the rear window and where in the interior of my blazer does the washer hose run.

Sounds like a problem within the wiper motor not turning off at rest or not reaching it's rest point to be able to turn itself off, probably needs a new motor. Disconnecting it should have no relation to the front washer operation, you can confirm this by reconnecting the wiper motor to try.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/oscar_403cc49e0f00cda7

Your rear bottle for the wipers should be at the back of the vehicle.Look in back for removable panel and bottle should be there.Turn your ignition on(no start)and activate rear washer Listen for the sound of the motor