Cars & Trucks Logo

Related Topics:

Kevin Phillips Posted on Jul 26, 2015
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Error code p1041 and p1047 02 chrysler sebring lxi 2.7L

1 Answer

johnny rebel

Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

  • Chrysler Master 10,875 Answers
  • Posted on Jul 27, 2015
 johnny rebel
Chrysler Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

Joined: May 12, 2013
Answers
10875
Questions
0
Helped
2937807
Points
47944

Definition of Diagnostic Trouble Code P1041 Saab: Injector Cylinder 4 Shorting To Ground

There is no definition for DTC P1047

CodeDescription P1192 Inlet Air Temp. Circuit Low P1193 Inlet Air Temp. Circuit High P1195 1/1 O2 Sensor Slow During Catalyst Monitor P1196 2/1 O2 Sensor Slow During Catalyst Monitor P1197 1/2 O2 Sensor Slow During Catalyst Monitor P1198 Radiator Temperature Sensor Volts Too High P1199 Radiator Temperature Sensor Volts Too Low P1281 Engine Is Cold Too Long P1282 Fuel Pump Relay Control Circuit P1283 Idle Select Signal Invalid P1284 Fuel Injection Pump Battery Voltage Out Of Range P1285 Fuel Injection Pump Controller Always On P1286 Accelerator Pedal Position Sensor Supply Voltage Too High P1287 Fuel Injection Pump Controller Supply Voltage Low P1288 Intake Manifold Short Runner Solenoid Circuit P1289 Manifold Tune Valve Solenoid Circuit P1290 CNG Fuel Pressure Too High P1291 No Temp Rise Seen From Fuel Heaters P1292 CNG Pressure Sensor Voltage Too High P1293 CNG Pressure Sensor Voltage Too Low P1294 Target Idle Not Reached P1295 No 5 Volts To TP Sensor P1296 No 5 Volts To MAP Sensor P1297 No Change in MAP From Start To Run P1298 Lean Operation At wide Open Throttle P1299 Vacuum Leak Found (IAC Fully Seated) P1388 Auto Shutdown (ASD) Relay Control Circuit P1389 No Auto Shutdown (ASD) Relay Output Voltage At PCM P1390 Timing Belt Skipped One Tooth or More P1391 Intermittent Loss of CMP or CKP P1398 Mis-Fire Adapter Numerator at Limit P1399 Wait To Start Lamp Circuit P1403 No 5 Volts To EGR Sensor P1475 Aux. 5 Volt Output Too High P1476 Too Little Secondary Air P1477 Too Much Secondary Air P1478 Battery Temp Sensor Volts Out of Limit P1479 Transmission Fan Relay Circuit P1480 PCV Solenoid Valve P1482 Catalyst Temperature Sensor Circuit Shorted Low P1483 Catalyst Temperature Sensor Circuit Shorted High P1484 Catalytic Converter Overheat Detected P1485 Air Injection Solenoid Circuit P1486 Evap Leak Monitor Pinched Hose P1487 Hi Speed Rad Fan CTRL Relay Circuit P1488 Auxiliary 5 Volt Supply Output Too Low P1489 High Speed Fan CTRL Relay Circuit P1490 Low Speed Fan CTRL Relay Circuit P1491 Rad Fan Control Relay Circuit P1492 Battery Temperature Sensor Voltage Too High P1493 Battery Temperature Sensor Voltage Too Low P1494 Leak Detection Pump Switch or Mechanical Fault P1495 Leak Detection Pump Solenoid Circuit P1496 5 Volt Supply Output Too Low P1498 High speed Rad Fan Ground CTRL Rly Circuit P1594 Charging System Voltage Too High P1595 Speed Control Solenoid Circuits P1596 Speed Control Switch Always High P1597 Speed Control Switch Always Low P1598 A/C Pressure Sensor Volts Too High P1599 A/C Pressure Sensor Volts Too Low P1602 PCM Not Programmed P1680 Clutch Released Switch Circuit P1681 No I/P Cluster CCD/J1850 Messages Received P1682 Charging System Voltage Too Low P1683 Speed Control Power Relay Or Speed Control 12 Volt Driver Circuit P1684 Battery Disconnected Within Last 50 Starts P1685 Skim Invalid Key P1686 No SKIM Bus Message Received P1687 No Cluster Bus Message P1688 Internal Fuel Injection Pump Controller Failure P1689 No Communication Between ECM & Injection Pump Module P1690 Fuel injection pump CKP Sensor Does Not Agree With ECM CKP Sensor P1691 Fuel Injection Pump Controller Calibration Failure P1693 DTC Detected In ECM Or PCM P1694 No CCD Messages Received From ECM P1695 No CCD/J185O Message From BCM P1696 PCM Failure EEPROM Write Denied P1697 PCM Failure SRI Mile Not Stored P1698 No CCD Messages Received From PCM P1719 Skip Shift Solenoid Circuit P1740 TCC Or OD Solenoid Performance P1756 Governor Pressure Not Equal To Target At 15?20 PSI P1757 Governor Pressure Above 3 PSI When Request Is 0 PSI P1762 Governor Pressure Sensor Offset Improper Voltage P1763 Governor Pressure Sensor Voltage Too High P1764 Governor Pressure Sensor Voltage Too Low P1765 Trans 12 Volt Supply Relay Control Circuit P1899 Park/Neutral Position Switch Stuck In Park or In Gear

Read more at: http://www.obd-codes.com/trouble_codes/dodge/
Copyright © OBD-Codes.com

4 Related Answers

Molson02536

Harvey N Tawatao

  • 3854 Answers
  • Posted on Jun 12, 2009

SOURCE: where is the fuel filter on a 99 chrysler sebring

The fuel filter on the Sebring is tucked up next to the tank towards the passenger side rear wheel. You can to pick up the fuel filter from Advance Auto Parts or Auto Zone for $25.00 Purolator Fuel Filter Part Number: F55302 Good luck and hope this helps. Auto Zone can give you the step by step to replacing the fuel filter free of charge.

Ad

Anonymous

  • 59 Answers
  • Posted on Jan 15, 2010

SOURCE: firing order for a 98 Chrysler SeBring LXI V-6

135
-------
246

Testimonial: "Thank you for your help!"

Anonymous

  • 360 Answers
  • Posted on Jan 30, 2011

SOURCE: how do i replace the starter on a 98 chrysler

2.5L (VIN N) Engine

  1. Disconnect the negative battery cable.
  2. Most vehicles will require the removal of the front exhaust pipe. Use penetrating oil on the fasteners to ease removal.
  3. Disconnect the starter motor electrical connections.
  4. Remove the starter motor mounting bolts and remove the starter.

tecnovative_68.gif To install:
  1. Clean both surfaces of the starter motor flange and the rear plate. This is important since the starter grounds through its case and the transaxle flange to which it attached. Some remanufactured starters may have paint on these areas which should be cleaned off before installation. Install the starter motor onto the transaxle and secure with the retaining bolts. Tighten the bolts to 20-25 ft. lbs. (26-33 Nm).
  2. Connect the electrical harness connectors to the starter.
  3. Connect the negative battery cable and check the starter for proper operation.

jturcotte

Jeffrey Turcotte

  • 8991 Answers
  • Posted on Oct 27, 2011

SOURCE: Need belt routing diagram for 2001 chrysler sebring lxi

Thanks for using FixYa.




jturcotte_2444.gif

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze



jturcotte_2445.gif

Fig. Accessory drive belt routing-Chrysler 2.7L engine





2.7L Engine
A/C & Alternator Belt

  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Loosen tensioner locking bolt and pivot bolt.
  4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:
  1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
  2. Adjust drive belt tension.
  3. Install the belt splash shield and right front wheel.
  4. Lower vehicle.
    jturcotte_2446.gif

    Fig. Installing A/C & alternator belt-2.7L engine


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and belt splash shield.
  4. Loosen the tensioner locking bolt and pivot bolt.
  5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:
  1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
  2. Adjust the drive belt tension.
  3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
  4. Lower the vehicle.

Power Steering Belt
  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Remove the air conditioning compressor/alternator belt.
  4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
  5. Remove the power steering belt.

To install:
  1. Install the power steering belt on pulleys.
  2. Adjust drive belt tension.
  3. Install the air conditioning compressor/alternator belt.
  4. Install the belt splash shield and right front wheel.
  5. Lower vehicle.


Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

I have a 1997 sebring lxi. It now will not turn over. I sprayed starter fluid in the intake and it turns over. I changed the fuel pump, fuel filter, and the relay. What else could it be?

Do you hear the fuel pump coming on normally comes on for approx 10 sec. when you turn key on, if no pump noise fault is still in fuel system, check the fuse and wiring, check for trouble codes, check injectors, etc
links below may help trouble shoot, press the helpful button

http://www.geeksoncars.com/how_4896626_troubleshoot-pump-problems-chrysler-sebring.html

1999 Chrysler Sebring LXi V6 2 5L

How to Test the Fuel Pump Chrysler 2 0L 2 4L
0helpful
1answer
0helpful
1answer

Ecm ecu computer is out on 99' chrysler sebring lxi

I have the same problem with my 99 sebring lxi, I'm getting a new ecu for the transmission and the engine, hopefully that fixes it. Did the car randomly die and wouldn't start again or when driving keep the transmission in one gear and wouldn't change?
3helpful
2answers

Tire specs for 2001 chrysler sebring

HI. Here is the complete line up of specs concerning your vehicles front and rear tires. You did not post the trim line of this car, so I posted all models and tire combination's specified by the manufacture.


2001 Chrysler Sebring Lim 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Coupe Front and Rear Tires P205/55R16
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Coupe Front and Rear Tires P215/50R17
2001 Chrysler Sebring LXi 4 Door Sedan Front and Rear Tires P205/60R16
0helpful
1answer

1996 Sebring: hi... i just bouth a used 1996 sebring lxi & h...

Buy a factory sensor from the dealer . Chrysler vehicles don't like aftermarket parts .
0helpful
1answer

Can you tell me what lxi stands for on a 2001 chrysler sebring convertible please

Hi,

LXI - L stands for Base Model and XI stands for Petrol.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
0helpful
1answer

1995 chrysler sebring lxi

there are four 18mm bolts on the opposite side of dust plate.once u remove thoe bolts,you'll have to either use a slide hammer, or the old fashion way a big hammer and smack it side to side.the whole hub and wheel bearing assembly will come out.The dust sheild is in between the hub and axel once it comes apart u will understand.
Not finding what you are looking for?

834 views

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...