Question about 2007 Dodge Nitro SLT

1 Answer

EGR valve how to replace

How do i remove and replace

Posted by on

  • 2 more comments 
  • jackie mcconnell
    jackie mcconnell Jun 25, 2015

    answer was not suitable. solution? bought 2016 fully loaded kia sentra

  • David Harrelson
    David Harrelson Jun 25, 2015

    I don't understand. Your fix was to buy a new car?

  • jackie mcconnell
    jackie mcconnell Jun 27, 2015

    yes in the last two months i spent over 1500 on repairs. every time i fixed something something else went wrong

  • jackie mcconnell
    jackie mcconnell Jun 27, 2015

    we bought it used in 02/13 in 20 mins off lots engine light came on got checked fixed that problem then something else went wrong every time problem got bigger and also i believe our chrysler dealer is not charging the appropiate rates to fix things so i got fed up with them so i got a brand new 2016 fully warranteed for seven years

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 5,440 Answers

Different on each engine. Buy shop manual for details and torque values.

Posted on Jun 18, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

EGR valve Mazda 2002 V-6 Tribute replacement


25348714-wbcquewu0r2lyixgzwrhmelx-3-0.gif

  1. Remove the EGR valve.
  1. Disconnect the vacuum line.
  2. Disconnect the EGR tube.
  3. Remove the EGR valve and discard the gasket.
NOTE: The EGR valve sealing surfaces are soft metals.

  1. To install, reverse the removal procedure.
  1. Carefully clean all sealing surfaces and install a new EGR valve gasket.

Jan 01, 2015 | 2002 Mazda Tribute

1 Answer

What is a egr valve


  1. Install a tachometer on the engine, following the manufacturer's instructions.
  2. Detach the engine wiring harness connector from the Idle Air Control (IAC) solenoid.
  3. Disconnect and plug the vacuum supply hose from the EGR valve.
  4. Start the engine, then apply the parking brake, block the rear wheels and position the transmission in Neutral.
  5. Observe and note the idle speed.
If the engine will not idle with the IAC solenoid disconnected, provide an air bypass to the engine by slightly opening the throttle plate or by creating an intake vacuum leak. Do not allow the idle speed to exceed typical idle rpm.
Using a hand-held vacuum pump, slowly apply 5-10 in. Hg (17-34 kPa) of vacuum to the EGR valve nipple.
  1. If the idle speed drops more than 100 rpm with the vacuum applied and returns to normal after the vacuum is removed, the EGR valve is OK.
  2. If the idle speed does not drop more than 100 rpm with the vacuum applied and return to normal after the vacuum is removed, inspect the EGR valve for a blockage; clean it if a blockage is found. Replace the EGR valve if no blockage is found, or if cleaning the valve does not remedy the malfunction.


EGR Valve Removal & Install
3.0L OHV (2 valve) and 3.4L SHO engines

b9175c5.jpg

Fig. : EGR mounting-3.0L OHV (2 valve) engine

5fcd84e.jpg

Fig. : EGR mounting-3.4L (SHO) engine

4552fc2.jpg

Fig. : Remove the two retaining bolts and...

b849310.jpg

Fig.: ... remove the valve from the intake manifold

795549d.jpg

Fig.: Thoroughly clean the mating surfaces of the manifold and the EGR valve (if being reused)
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hose from the EGR valve.
  3. Using a 22mm wrench or crowfoot, disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
  4. Remove the EGR valve mounting fasteners, then separate the valve from the intake manifold.
  5. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm).
  2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 26-47 ft. lbs. (35-65 Nm).
  3. Connect the vacuum hose to the EGR valve.
  4. Connect the negative battery cable.

3.0L OHC (4 valve)

d8a563e.jpg

Fig. : EGR mounting-3.0L OHC (4 valve) engine
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hose from the EGR valve.
  3. Remove the two EGR tube-to-EGR valve retaining nuts.
  4. Remove the EGR valve mounting fasteners, then separate the valve from the intake manifold.
  5. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm).
  2. Connect the EGR valve-to-EGR tube, then tighten the retaining nuts.
  3. Connect the vacuum hose to the EGR valve.
  4. Connect the negative battery cable.

Tell us news.

Oct 12, 2012 | 1998 Nissan Maxima

1 Answer

Just replaced EGR hose & valve copver gaskets on 2002 Ford Escape 4WD. Did test drive, runs really rough & almost stops & cuts off. Any ideas?


OK, if you replaced the EGR hose, did you go all the way to change the EGR Valve? A stuck open EGR Valve can cause a rough idle and almost make it cut off.
Also, a vacuum leak on the EGR valve can cause a rough idle.

prev.gif next.gif Exhaust Gas Recirculation (EGR) Valve Removal & Installation 2.0L Zetec Engine NOTE: When the EGR tube is disconnected from the EGR valve, it must be discarded and a new EGR tube must be installed. The aluminum threads on the EGR valve must be inspected, and a new EGR valve installed if the threads are damaged.
To Remove:
  1. Disconnect the negative battery cable.
  2. Remove and discard the exhaust manifold-to-EGR tube. Use the following as a guide:
  3. Raise and safely support the vehicle
  4. Remove the splash shield
  5. Disconnect the EGR tube fitting
  6. Lower the vehicle
  7. Remove the air cleaner outlet pipe
  8. Disconnect the EGR tube from the EGR valve.
  9. Detach the vacuum line and remove the two retainer bolts.
NOTE: The EGR valve sealing surfaces are soft metals and easily damaged.
To Install:
  1. Installation is a reverse of the removal process. Carefully clean all sealing surfaces and install a new EGR valve gasket.
  2. Install a new EGR valve tube.
Detach the vacuum line (#1) and unbolt the EGR valve - 2.0L 02-04_escape_emissions_022.gif

3.0L (4v) Engine To Remove:
  1. Disconnect the vacuum line.
  2. Disconnect the EGR tube.
  3. Remove the EGR valve and discard the gasket.
NOTE: The EGR valve sealing surfaces are soft metals and easily damaged.
To Install:
  1. Installation is a reverse of the removal process. Carefully clean all sealing surfaces and install a new EGR valve gasket.
Detach the vacuum line (#1), unthread the EGR tube (#2) and remove the EGR valve bolts (#3) - 3.0L (4V) 02-04_escape_emissions_023.gif

Aug 02, 2010 | 2002 Ford Escape

3 Answers

EGR Valve not working


EGR Valve Testing
  1. Install a tachometer on the engine, following the manufacturer's instructions.
  2. Detach the engine wiring harness connector from the Idle Air Control (IAC) solenoid.
  3. Disconnect and plug the vacuum supply hose from the EGR valve.
  4. Start the engine, then apply the parking brake, block the rear wheels and position the transmission in Neutral.
  5. Observe and note the idle speed.
If the engine will not idle with the IAC solenoid disconnected, provide an air bypass to the engine by slightly opening the throttle plate or by creating an intake vacuum leak. Do not allow the idle speed to exceed typical idle rpm.
Using a hand-held vacuum pump, slowly apply 5-10 in. Hg (17-34 kPa) of vacuum to the EGR valve nipple.
  1. If the idle speed drops more than 100 rpm with the vacuum applied and returns to normal after the vacuum is removed, the EGR valve is OK.
  2. If the idle speed does not drop more than 100 rpm with the vacuum applied and return to normal after the vacuum is removed, inspect the EGR valve for a blockage; clean it if a blockage is found. Replace the EGR valve if no blockage is found, or if cleaning the valve does not remedy the malfunction.


EGR Valve Removal & Install
3.0L OHV (2 valve) and 3.4L SHO engines

b9175c5.jpg

Fig. : EGR mounting-3.0L OHV (2 valve) engine

5fcd84e.jpg

Fig. : EGR mounting-3.4L (SHO) engine

4552fc2.jpg

Fig. : Remove the two retaining bolts and...

b849310.jpg

Fig.: ... remove the valve from the intake manifold

795549d.jpg

Fig.: Thoroughly clean the mating surfaces of the manifold and the EGR valve (if being reused)
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hose from the EGR valve.
  3. Using a 22mm wrench or crowfoot, disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
  4. Remove the EGR valve mounting fasteners, then separate the valve from the intake manifold.
  5. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm).
  2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 26-47 ft. lbs. (35-65 Nm).
  3. Connect the vacuum hose to the EGR valve.
  4. Connect the negative battery cable.

3.0L OHC (4 valve)

d8a563e.jpg

Fig. : EGR mounting-3.0L OHC (4 valve) engine
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hose from the EGR valve.
  3. Remove the two EGR tube-to-EGR valve retaining nuts.
  4. Remove the EGR valve mounting fasteners, then separate the valve from the intake manifold.
  5. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm).
  2. Connect the EGR valve-to-EGR tube, then tighten the retaining nuts.
  3. Connect the vacuum hose to the EGR valve.
  4. Connect the negative battery cable.

Tell us news.

May 04, 2010 | 1999 Mercury Sable

1 Answer

How do I locate and replace EGR valve?


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} EXHAUST GAS RECIRCULATION (EGR) VALVE REPLACEMENT

REMOVAL PROCEDURE
1. Turn OFF the ignition. 2. Disconnect the EGR valve electrical connector 3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back. 4. Remove the EGR valve retaining bolts. 5. Remove EGR valve assembly. 6. Remove the gasket. INSTALLATION PROCEDURE
1.
Install the EGR Valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions.
2. Install the bolts through the EGR valve. Tighten Tighten the bolts to 30 N.m (22 lb ft) 3. Connect the pipe assembly to the EGR valve. 4. Install the bolt. Tighten Tighten the bolts to 30 N.m (22 lb ft) . Connect the EGR valve electrical connector.

Jan 30, 2010 | 2001 Buick Regal

3 Answers

Location of EGR valve for 4.6 liter engine? how do you remove the EGR valve?


a887903.gif
EGR VALVE IS #2.

Please wait for second post to answer your second question....comes with a few pictures.

Nov 16, 2009 | 1992 Ford Crown Victoria

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

1 Answer

How do you replace egr valve in a 2005 dodge caravan


REMOVAL - 2.4L The EGR valve and Electrical EGR Transducer are serviced as an assembly.
  1. Disconnect vacuum tube from electric EGR transducer. Inspect vacuum tube for damage.
  2. Remove electrical connector from solenoid.
  3. Remove EGR tube bolts from EGR valve.
  4. Remove EGR valve from cylinder head adaptor.
  5. Clean gasket surface and discard old gasket. Check for any signs of leakage or cracked surfaces. Repair or replace as necessary

INSTALLATION - 2.4L The EGR valve and Electrical EGR Transducer are serviced as an assembly.
  1. Assemble EGR valve with new gasket onto the cylinder head adaptor.
  2. Loose assemble the bolts from EGR valve to EGR tube.
  3. Loose assemble the bolts from EGR valve to cylinder head.
  4. Tighten bolts from EGR valve to cylinder head to 22.8 N·m (200 ±25 in. lbs.) torque.
  5. Tighten bolts from EGR valve to EGR tube to 11.9 N·m (105 ±20 in. lbs.) torque.
  6. Reconnect vacuum hose and electrical connector to electrical EGR transducer.

Aug 03, 2008 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

EGR VALVE


REMOVAL PROCEDURE
  1. Turn OFF the ignition.
  2. Disconnect the EGR valve electrical connector.
  3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back.
  4. Remove the EGR valve retaining bolts.
  5. Remove EGR valve assembly.
  6. Remove the gasket.
INSTALLATION PROCEDURE
  1. Install the EGR valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions.
  2. Reinstall the bolts through the EGR valve into the intake manifold. Tighten Tighten the EGR bolts to 30 N.m (22 lb ft).
  3. Connect the exhaust pipe assembly to the EGR valve.
  4. Reinstall the exhaust pipe bolt. Tighten Tighten the nuts to 30 N.m (22 lb ft).
  5. Connect the EGR valve electrical connector

May 28, 2008 | 2000 Chevrolet Impala

Not finding what you are looking for?
2007 Dodge Nitro SLT Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...