Wiper fluid not working,is it a fuse or a motor ?

WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

sounds like a wire ws loose and finally fell off, check to see that it is plugged in at the motor. there is a fuse, manual will tell you which one and if no manual it may list it on the fuse cover. if the motor is bad it would still squirt fluid so as both are not working it probably isn't the wiper motor.

the washer fluid could be empty / the fuse for the wiper blew / the relay went bad /if you tried to use the wipers without clearing ice away you blew the fuse/ if you just put water in instead of washer fluid it's frozen/ if the wiper works and there is windshield fluid in the tank and not water and all fuses are good the pump motor for the fluid went and is easy to change

Your wiper and wiper fluid motors are different operation. The fluid one is a pump and the wiper motor only operates the wipers. Should check and see if you are getting power to the wiper motor if you are and the wiper does not work then you may need a new wiper motor.

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

CHECK WIPER FLUID LEVEL FIRST ALL IS GOOD CHECK FOR POWER AT WIPER WASHER PUMP MOTOR.IF NO POWER AT WIPER WASHER MOTOR.CHECK 15 AMP FUSE IN THE ENGINE COMPARTMENT FUSE RELAY BOX.IF YES YOU ARE GETTING POWER AT WIPER WASHER MOTOR.WIPER WASHER MOTOR FAULTY.

CHECK VOLTAGE AND GROUND AT WASHER PUMP MOTOR WHILE ACTIVATING UNIT. IF VOLTAGE AND GROUND PRESENT DEFECTIVE MOTOR,IF NOT DEFECTIVE SWITCH,FUSE

Its the same fuse that supplies power to the wiper motor so if the wiper motor is working than the fuse is good.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Most likely a bad washer fluid pump.

same fuse . Could also be washer switch. Needs to be checked out with 12V test light