Windshield wipers stopped working. Windshield wipers are stuck in the up position. Is there a way to get them down until I can get them fixed?

Hello. Simply remove the 'windshield wiper' fuse. It seems your windshield wiper motor is 'hard wired'; comes on when you turn on the ignition switch. That's not good!

Use vinegar to unfreeze

Could be loose wiper arm. Are the blades heavy. Too big of wiper blade will cause problems

The parking function is built into the motor assembly. We normally replace the assembly. If it is assembled with screws you may be able to open it and possibly repair it.

It sounds like the the circuit board has gone bad and does not know where the base is any more so it will stop at the middle or the windshield. Auto Zone should have a new board if it's replaceable like the GM products. Good luck and hope this helps, In the mean time you can always turn your wipers on and pull the fuse out when it's at the down position so it's not up.

• Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF

• Damaged turn signal and windshield wiper switch .
• Damaged windshield wiper motor .
• Damaged windshield wiper control module.

Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :

• Windshield wiper motor (17508) (F-type).
• Washer system.
• Windshield wiper control module.
• Turn signal and windshield wiper switch (13K359).

The windshield wiper control module is:

• Located at the instrument panel fuse panel.

The windshield wiper motor is:

• Attached to the cowl top extension (021A36) .
• Connected to windshield wiper mounting arm and pivot shaft (17566) .

The turn signal and windshield wiper switch features a:

• Rotary wiper switch.
• Push type washer actuator.

OFF/Low/High Speed

• Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
• The windshield wiper motor has a brush rigging that permits selection of low or high speed.
• When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
• When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
• In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
• When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
• When the park switch contacts open, the windshield wiper motor stops in the park position.

Interval
When the turn signal and windshield wiper switch is in the interval position:

• The wipers make single wipes separated by pauses.
• The rotary switch is on the end of turn signal and windshield wiper switch .
• The length of the pause can be set from approximately 1 to 17 seconds.
• Length of pause decreases as the rotary switch is rotated away from off.
• Length of pause increases as the rotary switch is rotated toward off.

While in the interval wiper mode:

• It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.
  

This is a commoon problem with what is called the "Park pawl stop". The tab is most likely bent and needs to be re-aligned, then the wipers need to be re-timed. This re-timing can be a little difficult, although the re-aligning of the tab is failry simple.

TechJK

You will need to replace the wiper transmission.This is a common problem.

This is an easy fix. Likely ice got on your windshield and froze your wipers to the glass then when turned on moved out of position. Take the cover off the base of the wipers and loosen the bolts. Put them down all the way and tighten. When wipers are turned on when frozen to glass the gears want to move but cant and loosens at the base. Please let me know if this does not help and will look into it further but this is probably it. Thanks

The fuse panel is under the instrument panel to the left of the steering column. Lift the handle to unlatch the panel and pull it down. The windshield wiper/washer system uses a circuit breaker in position #2 in the fuse panel. If your washer is working the circuit breaker is OK.