RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove Radiator
SOURCE: 97 Lincoln Contiental Drivers door ajar message
It is a sticky sensor in the door latch mechanism. Spray it w/ WD-40 and follow up with a dose of silicone spray. Open/close doors several times and it should be ok. If you have a problem with 1 door the other 3 are sure to follow---DO THIS TO ALL 4 DOORS!!!!!!!!!
SOURCE: how to replace an alternator on a 96 lincoln continental 4.6 V8
take out the top 4 bolts above the altenator, between those metal tubes on the metal bracket. then u have 1 bolt holding the wires to the altenator on that bracket aswell remove that. then remove the coolant reserve bottle and stick a breaker bar or rend of a ratchet in the tenchenor pulley square slot pull it back twords the head lights the belt will loosten then remove it from the altenator. then u will see 2 more bolts on the bottom side of the altenator by the pulleys and belt. Remove them 2 bolts all the way and the altenator will drop out of the bottom of them metal tubes and slide through the sides of them and its out... its very ez and does not need the tubes removed its a lot ezer than it looks.. sorry about my spelling im an infantryman not a teacher.
SOURCE: where do i spray quick start fliud in a 96 lincoln
Do not spray starting fluid in your engine!!!!!!!! You can and will do damage to your engine. Not Recommended!!!!!!
SOURCE: 2002 LS: aHow do I fill radiator in my V8 Lincoln LS...
First- to drain ,you can reach the drain valve,from the pass side,if you lay on the ground and reach up to the radiator. You do not even have to raise the vehicle up
Second- mix Yellow GO5 Coolant about 50/50 or 60/40. Do not use Green in a Ford or Orange GM
To Fill- Remove the front two plastic screw type buttons,from the engine cover
-Remove the cover
The radiator cap is on the front of engine,on top,it is plastic
Remove cap and that is your fill point
Run engine to warm and get thermostat open,as you would with any vehicle
Top off coolant,replace cap
VERY IMPORTANT-next to the Power Brake Booster,and just under it,is a BLEEDER HOSE;to let air out of system. Turn screw slot ,only a little,DO NOT REMOVE SCREW. When coolant runs out close.
Fill-Degas Bottle,to full line,with coolant.
Check the next couple days on resevoir level ( Degas Bottle)
917 views
Usually answered in minutes!
×