How to replace rear motor mount for 1997 mazda protoge

https://www.google.com/search?q=Where+is+obd2+port+on2002+mazda&biw=1362&bih=650&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwjb68P25JrQAhWC14MKHUfwDxgQsAQIMg#tbm=isch&q=How+do+i+replace+a+cam+seal+on+a+94+mazda+protoge

Hope this helps

1-10 scale....4-5

There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.



1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..



1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

REMOVE**** FRONT SHOCKS, FIRST OF ALL.SUPPORT THE LOWER CONTROL ARM WITH A JACK,REMOVE FRONT WHEEL, REMOVE BRAKE HOSE AND ABS SENSOR HARNESS TO THE STRUT BOLTS OR CLIPS,REMOVE ACTUATOR FROM TOP OF THE STRUT,IF EQUIPPED WITH AUTOMATIC ADJUSTING SUSPENSION. PAINT ALIGNMENT MARKS ON THE UPPER STRUT MOUNTING BLOCK AND STRUT TOWER AND ON THE LOWER STRUT MOUNT TO STEERING KNUCKLE SO THAT CAN BE REINSTALLED IN THE SAME POSITION. REMOVE UPPER STRUT MOUNTING NUTS, REMOVE THE STRUT TO KNUCKLE BOLTS,REMOVE STRUT ASSEMBLY.TO INSTALL ***** INSTALL STRUT INTO THE STRUT TOWER ALIGNING THE PAINT MARKS MADE DURING REMOVAL.INSTALL UPPER MOUNTING NUTS AND TIGHTEN TO 34 - 46 FT LBS. INSTALL STRUT TO KNUCKLE BOLTS TIGHTEN TO 55 - 61 FT LBS. INSTALL ACTUATOR AND ENGAGE THE ELECTRICAL CONNECTOR IF EQUIPPED WITH AAS. INSTALL BRAKE HOSE AND ABS SENSOR HARNESS CLIPS OR BOLTS.INSTALL WHEEL AND CHECK ADJUST THE FRONT END ALIGNMENT. TO ( REPLACE REAR SHOCKS ) REMOVE REAR WHEELS, REMOVE REAR PACKAGE TRIM. REMOVE SPEED SENSOR HARNESS, REMOVE TOP STRUT NUTS,THE SUSPENSION WILL DROP WHEN THE WEIGHT LIFTS OFF THE WHEELS. REMOVE BOTTOM STRUT BOLTS.REMOVE STRUT ASSEMBLY.TO INSTALL ***** INSTALL STRUT ASSEMBLY, INSTALL BOTTOM STRUT MOUNT BOLTS AND TIGHTEN TO 55 - 61 FT LBS.INSTALL UPPER MOUNTING NUTS AND TIGHTEN TO 33 - 46 FT LBS. INSTALL SPEED SENSOR HARNESS.INSTALL REAR PACKAGE TRIM. INSTALL REAR WHEELS.

I don't recommend heating it . But if you have a wiz wheel use it and cut the nut off. Especially if your replacing the entire axle.

Front Wiper Motor Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the windshield wiper mounting arm and pivot shaft
   WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
   NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
   
3. Remove the 3 bolts and the wiper motor.
   
   
   
   Fig. Wiper motor and linkage
   

To install:

1. Install wiper motor and bolts.
2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
3. Install windshield wiper mounting arm and pivot shaft.
4. Check wiper operation.

Rear Wiper Motor - Removal & Installation

1. Remove the rear pivot arm.
2. Remove the rear wiper motor shaft nut cover
3. Remove the rear wiper motor shaft nut.
4. Open the lift gate window.
5. Remove the rear wiper motor cover trim panel.
6. Disconnect the electrical connector.
7. Remove the 2 rear window wiper motor nuts
8. Remove the rear window wiper motor.
   
   
   Fig. Rear wiper motor view-2008 model shown, other years similar
   

To install:

1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
2. Reconnect the electrical connector.
3. Install wiper motor cover trim panel.
4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
5. Install shaft nut cover.
   
6. Check wiper operation.

Good luck (remember rated this post).

Not too hard but you have to remove the wheels and go into the trunk to remove the to nuts, under a cover.....

There should be a tensioner pully on your motor like in the middle some where it should move with a wrench on it and that keeps your belt tight. Do you have a one big belt or a couple of small ones?

http://autos.groups.yahoo.com/group/villagerquest/

it's usually called the trans mount cause that's what's on that side.

Section 02-03: Engine and Transaxle Mounting 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Support Insulator, Front Transaxle Removal

1. Remove the battery (10655). Refer to Section 14-01 for the removal procedure.
   
2. Remove the Engine Air Cleaner (ACL) (9600). Refer to Section 03-12 for the removal procedure.
   
3. Remove the radiator coolant recovery reservoir (8A080). Refer to Section 03-03 for the removal procedure.
   
4. Remove the battery tray (10732). Refer to Section 14-01 for the removal procedure.
   
5. Support the transaxle with a floor jack.
   
6. Remove the front transaxle support insulator through bolt and nut.
   
7. Remove the three front transaxle support insulator bolts and the front transaxle support insulator.
   

-----------------------------------------------------------
Support Insulator, Rear Transaxle Removal

1. Remove the rear transaxle support bracket. Refer to the procedure in this section.
   

1. Raise and support the vehicle.
   

1. Remove the three rear transaxle support insulator nuts.
   
   
   
   
   

1. Lower the vehicle.
   

1. Remove the rear transaxle support insulator from the vehicle.
   

follow the top radiator hose to the engine remove the bolts on thermostat housing be carefull removing those bolt not to break them let me know pierre