Remove the inner door panel then disconnect the arms that run from the outside door handle, the inner door handle, the door lock mechanism, from each unit. then undo the 3 bolts/screws on the end of the door to remove the door latch assembly.
Posted on Jul 20, 2015
Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Good luck!
Posted on Jan 02, 2017
SOURCE: Replace starter on 1992 GMC Sierra pickup truck
First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.
Posted on Feb 14, 2009
SOURCE: My Power window on my 2003 GMC Sierra 1500 Truck
if your main switch panel still works the passenger window and if door locks still work probaly bad window motor
Posted on Oct 21, 2009
SOURCE: 2004 gmc 1500 sierra heater control stuck on
Defrost is the default position. Is the control a autyomatic temperture control unit? ( you set the temp and select automatic) if it is the system is completely electronic. You push the buttons and the control still says defrost or can you select something else and the control shows it but it just keeps coming out the defrost? If the control changes and the air comes out the defrost anyway and the cheack engine light isn't on, then the problem can be blown fuses or an air door actoater not working. Does the dash emit a clicking sound? if it does with the covers off the bottom of the dash reach around touching the different pieces till you touch the idem that is clicking. this is an acutor motor, or blend door motor. they have gears in them that wear out and break the motors aren't repairable and you just replace the ofending motor. the door that is moves can be stuck. and may have to be freed up with blaster, WD40, or other rust buster till it moves easy. maybe after getting the door to move smoothly you can get the old motor to move the door wiithout having to install a new one.
Posted on Jan 06, 2010
SOURCE: 1990 GMC Sierra 1500 pickup. Windshield wipers, Cruise Control
May want to look at replacing the wiper circuit board.It is located on the firewall adjacent to the wiper motor and has a some what square black cover with 3 torx screws and wireing harness pluged into the side.We had a truck that every time you washed it the wipers would stay on until it dryed out.You can try removing it and spaying it down with contact cleaner just watch the brease on the two contact tips.Well hope this helps.
Posted on Feb 05, 2010
SOURCE: LOW OIL PRESSURE ON 2007 GMC SIERRA 1500. CHANGED
have it tested using a manual gage if still low then main baring ore most likely bad that would mean a over hall if is really low and bearings bad should be making rattle noise when started up first few seconds
Posted on Mar 11, 2010
Testimonial: "thanks alot.truck is not making a rattling noise.we did check it with a manual gauge.it read about 10 at idol. press. gets better as you incr speed"
Mar 05, 2015 | 1992 GMC Sierra
Jan 07, 2015 | 1992 GMC Sierra
Jan 07, 2015 | GMC Cars & Trucks
Nov 06, 2010 | 1992 GMC Sierra
Aug 30, 2010 | 2000 GMC New Sierra 1500
Mar 31, 2010 | 1992 GMC Sierra
Mar 08, 2010 | 1992 GMC Sierra
Dec 03, 2009 | 1997 GMC Sierra
Jul 30, 2009 | 2007 GMC Sierra Classic
Jun 18, 2009 | 1992 GMC Sierra
154 people viewed this question
Usually answered in minutes!
×