Question about Chevrolet Cars & Trucks
If the battery is good you will need to follow flow. Test light is the easiest to use. First hook light to ground and touch pos terminal,lights good next touch pos battery cable end, lights good. Next follow pos cable to starter pos terminal,lights good. Next hook test light to bat pos teminal,touch neg terminal,lights good. Then touch engine block, lights good ground. Next move test light clamp back to ground/neg side and touch alt pos terminal,lights good.if all that tests good, if all good move inside and check for power at ign switch pos term if at any time you dont find power you have wiring issue that needs to be addressed. Let me know what you find. Russ
Posted on Mar 29, 2015
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Car battery won't stay charged.
jumped battery started next day attempted to start and was dead i swapped out a battery no good then i swapped out the terminals to the battery and it started right up
Posted on Aug 13, 2008
Last night I checked the battery and it was still good. I disconnected and then reconn ected both terminals and that brought the power back. When I turned the key the power went out again. I repeated the procedure but did not turn the key. Instead, I took off the knee bolster and tried to wiggle the wires under the dash to see if I could find the source since it seems to be related to the ignition. Nothing cut the power so I started it up and it worked fine except for the check engine light which was flashing that says I have a misfire condition. I drove the car 25 miles to work this morning and will be taking it to the dealer for a better inspection.
Posted on Aug 22, 2008
OK if only 4 months old, charge it with an external battery charger. Once vehicle is running the quick and still most valid test I make is:
Running, with no accessories on, charge volts on volt meter (not dash gauge) should read between 12.9 &14volts. Turn all accessories and headlights on high beam. Volts should not read below 12.5v at idle and should not creep lower after running at any time, even after ten or fifteen minutes. If voltaqge is not as specified alternator has failed and needs replacement.
Posted on Apr 22, 2009
Check the ECM for Codes to help you find out what's causing the problem. Here is a simple and easy way to check.
On board diagnostic (OBD) was designed on vehicles equipped with electronic fuel injection so you can generally retrieve the codes yourself. No need buying a scanner or running to any parts stores to check the Check Engine. This system is called obd1 and applies to most vehicles made before 1995 for domestics and 1993 on imports. In this article, I will discuss the methods used by domestic vehicle manufacturers on how to check the engine lights in their cars and Trucks.
For GM domestic vehicles made before 1995, the diagnostic connector is located under the dash panel by the driver side. To get the check Engine codes to flash in your dash panel, use a jumper wire or a paper clip and connect terminals A and B of the diagnostic connector. Turn your ignition key on with engine off and the codes should start to blink. All codes should start with code 12 which is one long flash followed by 2 short flashes. This code 12 means the diagnostic system is normal and will repeat itself continuously if there are no trouble codes. Otherwise, code 12 will flash 3 times before flashing the fault codes.
Counting the codes being flashed is easiest way to trouble shot problems in domestic vehicles and most of the codes can be erased or cleared by disconnecting the battery negative terminal for 1 minute and reconnect. Just make sure to check your service manual in case you have electronic equipment such as radio or clock that needs reprogramming in which battery disconnection is not recommended. Finally after performing repairs on the culprit code, always go for a road test to confirm if the problem is fixed.
Here is a link with the GM codes. http://chevythunder.com/199295_lt1_trouble_codes.htm
Good luck and hope this helps
Posted on May 02, 2009
Tips for a great answer:
Feb 15, 2014 | Cars & Trucks
Aug 25, 2013 | 2001 Volkswagen Jetta TDI
Apr 02, 2013 | Cars & Trucks
Jan 25, 2013 | 2000 Chevrolet Venture
Mar 10, 2010 | 2001 BMW 325
Oct 28, 2009 | 1998 Toyota Camry
Nov 19, 2008 | Saturn SC2 Cars & Trucks
Aug 21, 2008 | 1996 Subaru Legacy
165 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: