The sunshade on my 01 chrysler sebring lxi it got jam in the middle of closing it.. How can i fix that?

Harvey N Tawatao

• 3854 Answers
• Posted on Jun 12, 2009

SOURCE: where is the fuel filter on a 99 chrysler sebring

The fuel filter on the Sebring is tucked up next to the tank towards the passenger side rear wheel. You can to pick up the fuel filter from Advance Auto Parts or Auto Zone for $25.00 Purolator Fuel Filter Part Number: F55302 Good luck and hope this helps. Auto Zone can give you the step by step to replacing the fuel filter free of charge.

SOURCE: firing order for a 98 Chrysler SeBring LXI V-6

135
-------
246

Testimonial: "Thank you for your help!"

SOURCE: how do i replace the starter on a 98 chrysler

2.5L (VIN N) Engine

1. Disconnect the negative battery cable.
2. Most vehicles will require the removal of the front exhaust pipe. Use penetrating oil on the fasteners to ease removal.
3. Disconnect the starter motor electrical connections.
4. Remove the starter motor mounting bolts and remove the starter.

1. Clean both surfaces of the starter motor flange and the rear plate. This is important since the starter grounds through its case and the transaxle flange to which it attached. Some remanufactured starters may have paint on these areas which should be cleaned off before installation. Install the starter motor onto the transaxle and secure with the retaining bolts. Tighten the bolts to 20-25 ft. lbs. (26-33 Nm).
2. Connect the electrical harness connectors to the starter.
3. Connect the negative battery cable and check the starter for proper operation.

Jeffrey Turcotte

• 8991 Answers
• Posted on Oct 27, 2011

SOURCE: Need belt routing diagram for 2001 chrysler sebring lxi

Thanks for using FixYa.

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze

Fig. Accessory drive belt routing-Chrysler 2.7L engine

2.7L Engine
A/C & Alternator Belt

1. Raise and safely support the vehicle.
2. Remove the right front wheel and belt splash shield.
3. Loosen tensioner locking bolt and pivot bolt.
4. Rotate tensioner clockwise to allow enough slack to remove belt

1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
2. Adjust drive belt tension.
3. Install the belt splash shield and right front wheel.
4. Lower vehicle.
   
   
   

   Fig. Installing A/C & alternator belt-2.7L engine
   

1. Before servicing the vehicle, refer to the Precautions Section.
2. Raise and safely support the vehicle.
3. Remove the right front wheel and belt splash shield.
4. Loosen the tensioner locking bolt and pivot bolt.
5. Rotate tensioner clockwise to allow enough slack to remove the belt

1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
2. Adjust the drive belt tension.
3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
4. Lower the vehicle.
   

1. Raise and safely support the vehicle.
2. Remove the right front wheel and belt splash shield.
3. Remove the air conditioning compressor/alternator belt.
4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
5. Remove the power steering belt.

1. Install the power steering belt on pulleys.
2. Adjust drive belt tension.
3. Install the air conditioning compressor/alternator belt.
4. Install the belt splash shield and right front wheel.
5. Lower vehicle.