Instructions how to install right rear tail light unit

You don't need to remove the rear bumper cover to remove the tail light units. See the link.
Chevrolet Impala 2014 2018 Tail Light Housing Removal

first remove the wire you hook up rear tail and break circuit. (1)install ground wire to the frame (2)turn on the head light switch and go to the rear to find the +12 volt on the wire then hook it up to the led tail circuit, it should only light up that circuit but if both still come on then the new led unit is not config right. Replace it or have it modified. if only the tail circuit is on then go to (3)cut off the head light switch and have someone step on the break peddle then fine the +12 volt on the wire and hook it up to the brake led circuit.(only the brake circuit should be on) hope this help you. .

Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn

Inside kick panel

Rear iignts in rear na, removing and instaiiing

Fig. 325: Rear Lights In Rear Lid, Removing And Installing

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Removing

CAUTiON: • Switch off all electrical components.

. . Switch ignition off and remove ignition key.

o Turn light switch into "0" position.

o Open cap - 1 - for warning triangle.

o Rotate quick-release screw - 2 - counter-clockwise 90 C and remove cover - 3 - from luggage compartment lining - direction of arrow -

Fig. 326: Removing Bulb Socket From Housing, Pressing Catch Bracket Downward

Courtesy of VOLKSWAGEN UNITED STATES, INC.

o Disconnect electrical harness connector

o Remove bulb socket - 1 - from housing, press catch bracket - 2 - downward - arrow - to do so

Fig. 327: Identifying Nuts, Clamping Bracket, Inner Tail Lamp, And Clamp Mounting

Courtesy of VOLKSWAGEN UNITED STATES, INC.

o Unscrew nut - 2 - and remove clamping bracket - 1 -

o Remove nut - 4 - and remove inner tail lamp - 3 - toward outside

o Remove clamp mounting - 5 - from body cut-out

Fig. 328: Identifying Clamp Mounting, Nuts, Inner Tail Lamp, And Tabs

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Installing

Installation is the reverse of removal, noting the following:

NOTE: • Make sure seal between body and tail lamp housing seals properly.

. Attach clamp mounting -2 - at inner tail lamp and screw on nut -3 - loosely.

. Attach inner tail lamp -4 - at body cut-out and make sure grip tabs - arrows - of clamp mounting rest against body cut-out

. Slide clamp mounting - 1 - onto threaded pin of inner tail lamp and tighten nuts - 3 - and -5 -.

Remove the interior on the rear body panel, you will see 2 black wing nuts that can be hand turned to remove the tail light plus there might be a additional two screws or bolts on the outside inner of the taillight as you open the trunk lid. 4 in total. slide the light out and replace the burned out light bulb. and reverse the removal instructions
Good Luck

Hi

Open rear hatch,
locate 3 philips screws on the right side of lamp,
note that the lamp assembly is held into the fender side by a plastic tab( hidden ). You have to stand at the rear fender side, facing the lamp and pull the lamp toward you carefully.

Thanks for using FixYa.
- Steve

Hi remove the tail light and remove the electrical connector then remove the top globe by twisting it anti clock wise then bend the contacts on the tail light up slightly and install the globe and tail light back

and Repair Notes TAIL LAMP REPLACEMENT REMOVAL PROCEDURE Open the rear compartment. Remove wingnut and pull back the rear compartment trim panel from the tail lamp. Remove the wingnuts from the tail lamp. Remove the tail lamp from the rear body panel. Disconnect the electrical connector from the tail lamp. Remove the tail lamp socket, turning counterclockwise. Remove the bulb from the tail lamp socket. Remove the sidemarker lamp socket, turning counterclockwise. Remove the bulb from the sidemarker lamp socket. INSTALLATION PROCEDURE Install the bulb to the tail lamp socket. Install the bulb to the sidemarker lamp socket. Install the sidemarker lamp socket, turning clockwise. Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.

Tail Lamp Assembly
Removal & Installation
To Remove:

1. Open the rear compartment.
2. If equipped, disconnect the cargo net.
3. Remove the wingnut and pull back the rear compartment trim panel.
4. Remove the wingnuts from the tail lamp assembly.
5. Remove the tail lamp assembly from the rear body panel.
6. Disconnect the electrical connector from the tail lamp assembly.
7. Remove the tail lamp socket by turning counterclockwise.

1. To Install:
2. Install the tail lamp socket by turning clockwise.
3. Connect the electrical connector to the tail lamp assembly.
4. Position the tail lamp assembly to the rear body panel.
5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
7. If equipped, connect the cargo net.
8. Close the rear compartment.

Please don't forget to rate !!!!!!