Is it a fuse that needs changing on an 08 nitro as fob and inside door locks not working

turns fail. 2003.?
so did not check all fuses first then scan the OBD2 port next
ooops, why skip those?

lots they are what do they all do good and bad.?
well fuses are blown why skip step on, electrics, all fuses checked,
"changed flasher"<<, why say that. then not say turns and hazards fail too or not????? i have a real oem shop manual for this car. USA spec car is it>?
w cant guess countries of VIN to know it
chapter 8w wiring, is clear and easy to read.

8w-60 and 61 locks and windows. schematics and all
not the fuse for windows it runs both sides. F12 , 50amps.
do door locks fail using key fob??????????? any?
F12 also runs door locks but is not bad. only for 1 door.

right door inside lock controls dead?too?
you have a fob
and lots of door controls switches, it is clear which fail and do not
front and rear, both.

the door control modules on this car use COMM buse
called PCI serial bus this car
so commands from any in car button or fob must work and send commands to t the door commanded, via PCI bus.
same goes for windows ,door control modules

bad comms
or the origination command device fails, the FOB or the door buttons afail
all doors have controls do only right side fail and fob too?

try testing at all doors first
and the fob too.
off hand seems PCI bus wires damaged on the right side.

Common Reasons Why Your Car Door Isn't Locking Properly The key fob battery is dead: This is one of the most common reasons why your car door lock is not working. If your locks aren't working, replacing the battery in the key fob could solve the issue. The key fob is faulty: If the battery isn't the problem, the issue may be with the fob itself. If you go to your car dealer, they can hook the fob up to a computer and make sure that the programming is still good. If it's not sending a signal, the fob will likely have to be replaced. A fuse is blown: If one door doesn't work, but others do, the problem could be a blown fuse. Replacing the fuse will correct the problem. This is a cheap and easy fix The solenoid is bad: Again, if one door doesn't work, but others do, the problem could be with the door lock solenoid. Replacing it may require removing the car door panel You have a broken wire: If the lock isn't getting power, hold the lock switch either up or down, and then open and close the door repeatedly to see if the lock will work. If it works sometimes, you probably have a broken wire

redux, now that the facts are stated.

the fob is dead, ok,, but more important
both door controls are dead., but does the rear hatch lock work and lift glass?
next is fuses, its always first, for any electric failure of any kind, means almost everything, no?

1: so both switches are dead.
2: and the door lock solenoids are silent.
3: that means the BCM is not working.

the body computer listens to both lock switches
left and right and they are not related.
in fact the switches are just 2 pins,
one ground and one MUX.

that means the BCM has issues.
next is scan it.

my quote, you cant fix modern cars lacking a scan tool, you can't , unless wild gue$$ing is fun or cheap.
both locks fail, BCM is NOT listening,
fact.

BCM is a computer, and its not responding
to valid door commands.
scan it. page 8L 171 in the FSM tells you just that.

ps: the mirrors do not use the BCM or power from locks. so has zero to do with locks.

the FOB receiver in the body (RKE) to make the fob work is called the SKREEM.
the skreem then sends cammands to BCM via the PCI buss. so id bet SKREEM is ok but the BCM has issues.

The BCM is now ignoring 3 major inputs
SKreem
door left mux switch
door right mux swtich.

scan it , id bet there DTC error from BCM
i bet.......

it maybe the BCM may have a problem or needs to be reset.

key in ignition 2 number 2 then press the fob. till doors lock. 2 to 3 times then unlock with fob. turn back key lock car. then un lock. then do the same with the other fob.

You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Yes, insure that you have power to the trunk lock inside trunk, If not could be lose/broken wire or shot fuse. I am sure the key fob does work for the doors? If not have key fob battery replaced. Also, a quick check on power to trunk lock, check to see if have remote power button inside car, if it works power is good. Defective key fob would then be indicated.

I had the same problem . Free solution was to pull yellow 20A IOD fuse in right front corner of fuse box under hood, wait 10 seconds, then reinsert fuse. Should solve problem as long as you don't lock doors with FOB. You can unlock doors with FOB, but apparently locking with FOB causes the problem. Otherwise you can pay to have the computer reset at the dealer, but the free solution worked for me.

To get inside the car .... Use the key in the lock cylinder, unlock the drivers door to get inside. You shouldn't have to reprogram the fob unless it or the keyless module was changed. There may be a blown fuse that supplies the keyless control module (check the owners manual for location). or wires that lead into the Drivers door may be damaged ... The keyless module is located inside the drivers door at the bottom behind the door panel ... do the unlock/lock and trunk release switches on the inside of the drivers door operate the locks and or trunk release? If so it is not the fuse ... and not the wires to it ... And it could be your BCM body control module, located in the dash board to right of your gas petal. Because the number entry keypad (code for that is on the inside of the right passenger trunk bracket arm) also doesn't work I assume it's not the key fobs themselves. Your 98 manual is correct for your car.