I have replaced my washer motor twice already, both times ending up with the same result wipers stop in up position. In addition I replaced the multi function switch and the iww module under the dash on my 94 ford ranger. Still have same problem

Did you check fuse's & relays ?
Rear Window Wiper Operation
The rear wiper motor is controlled by the SJB. The SJB supplies power to the rear wiper motor from the integrated rear wiper relay. The SJB will activate the relay when all of the following conditions are met:

• Ignition switch is in the ON position
• Liftgate glass and liftgate are closed
• Multi-function switch is in the ON or intermittent position

The SJB also supplies voltage to the rear wiper motor from SJB fuse 21 (15A) when the ignition switch is in the ON position. This power feed is used to continue the wipe cycle when the multi-function switch is turned to the OFF position. The SJB receives inputs from the multi-function switch that applies ground to the low speed wipe input or applies ground to the intermittent wipe input. When either of these circuits are grounded, the SJB activates the integrated rear wiper relay and power is supplied to the rear wiper motor to move the rear wiper motor from the park position. An internal switch in the rear wiper motor then moves to the run position which connects the accessory relay power to the rear wiper motor. When the rear wiper motor returns to the park position, the internal switch in the rear wiper motor moves back to the park position. If the multi-function switch is in the ON position, the rear wiper relay is still activated, power is supplied to the rear wiper motor, and the wipe cycle starts again. If the multi-function switch is in the intermittent position, the rear wiper relay does not activate until the predetermined dwell time has elapsed, at which time the SJB activates the rear wiper relay and the wipe cycle starts again. The SJB is the smart junction box .(computer )

Rear Washer System
The SJB supplies power to the rear washer pump from fuse 21 (15A) when the ignition switch is in the ON or ACC position. The rear washer pump receives ground from the multi-function switch when the wash function is turned ON. The multi-function switch also signals the SJB when the rear wash is activated and the SJB then activates the rear wiper.

It should be a short circuit or a bad relay. Good luck.

Have a qualified repair shop check it out . Electronic module involved , WCM - wiper control module . May have code's stored . You have no clue as to how it works.

The windshield wipers are controlled by the wiper control module and the driver-operated multi-function switch on the steering column, with the ignition switch in RUN or ACC position.
There are four modes of wiper operation: OFF position, the wipers move to and stay in the park position; Interval position, the wiper control module causes the wipers to cycle, separated by pauses, pause time length being determined by switch location; LO position, the wipers will operate at low speed continuously; HI position, the wipers will operate at high speed continuously.
The windshield washers are controlled by pressing inward on the wiper switch end of the multi-function switch. The washers will operate as long as the switch is depressed. If the wipers are in the OFF or Interval operating mode, the wipers will begin in LO speed and the washer pump will pump fluid from the reservoir to the nozzles. When the switch is released, the wipers will complete three cycles and then return to their previous setting. In LO or HI mode, no change in wiper operation will occur during washer operation.
The washer fluid level sensor is in the windshield washer reservoir (17618) and is monitored by the hybrid electronic instrument cluster (HEC) and displays a WASHER message when the fluid level is low. The washer fluid level sensor and windshield washer reservoir are replaced as an assembly.

• The Low Wiper Speed Does Not Operate Properly

• Multi-function switch.
• Wiper motor.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test C .

• The High Wiper Speed Does Not Operate Properly

• Multi-function switch.
• Wiper motor.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test D .

Highly doubtful it being a blown fuse . Fuse's don't just blow , short circuit to ground or high current draw . Faulty component , wiper motor , wiper control module more likely . Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size . Under system click on body & accessories . then under subsystem click on wiper / washer , Click the search button ,then the blue link . Looking at the diagram i see the wiper switch is a input to the wiper control module .

The windshield wipers are controlled by the wiper control module and the driver-operated multi-function switch on the steering column, with the ignition switch in RUN or ACC position.
There are four modes of wiper operation: OFF position, the wipers move to and stay in the park position; Interval position, the wiper control module causes the wipers to cycle, separated by pauses, pause time length being determined by switch location; LO position, the wipers will operate at low speed continuously; HI position, the wipers will operate at high speed continuously.
The windshield washers are controlled by pressing inward on the wiper switch end of the multi-function switch. The washers will operate as long as the switch is depressed. If the wipers are in the OFF or Interval operating mode, the wipers will begin in LO speed and the washer pump will pump fluid from the reservoir to the nozzles. When the switch is released, the wipers will complete three cycles and then return to their previous setting. In LO or HI mode, no change in wiper operation will occur during washer operation.
The washer fluid level sensor is in the windshield washer reservoir (17618) and is monitored by the hybrid electronic instrument cluster (HEC) and displays a WASHER message when the fluid level is low. The washer fluid level sensor and windshield washer reservoir are replaced as an assembly.

• The Wipers are Inoperative

• Fuse.
• Wiper motor.
• Multi-function switch.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test B .

PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

• Is the fuse OK?

Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.

• Is the voltage greater than 10 volts?

Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.

• Are the resistances less than 5 ohms?

Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .

• Is the multi-function switch OK?

Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).

• Is the resistance less than 5 ohms?

Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).

• Is the resistance less than 5 ohms?

Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).

• Is the voltage greater than 10 volts?

Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.

• Is the resistance less than 5 ohms?

Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.

Do you know how to use a volt meter ? Need to check for voltage at the motor ! , need a wiring diagram. Most of the time other people on here will tell you to check the fuse's , that doesn't end up being the cause ! Most of the time it's the motor or a wiring problem ! I have seen the wire in side the rubber boot ,when you open the rear hatch break causing a no power situation to the motor . If you open the rear hatch ,door ,lift gate , what ever you call it . If you look when it is open there is a rubber boot connecting the body to the door , there are wires in side . There have been known to break ! This next part is a FORD pinpoint test. This is how ford says how to check !
PINPOINT TEST B: THE WIPERS ARE INOPERATIVE - REAR WINDOW Test Step Result / Action to Take B1 CHECK CIRCUITS CBP43 (GY) AND SBP19 (BU/RD) FOR VOLTAGE

• Key in OFF position.
• Disconnect: Rear Wiper Motor C476.
• Key in ON position.
• Measure the voltage between rear wiper motor C476-3, circuit CBP43 (GY), harness side and ground; and between rear wiper motor C476-4, circuit SBP19 (BU/RD), harness side and ground.
  >
• Are the voltages greater than 10 volts?

Yes
GO to B2 .

No
VERIFY SJB fuse 43 (5A) and fuse 19 (25A) are OK. If OK, REPAIR the circuit(s) in question. TEST the system for normal operation. B2 CHECK CIRCUIT GD150 (BK/WH) FOR OPEN

• Key in OFF position.
• Measure the resistance between rear wiper C476-1, circuit GD150 (BK/WH), harness side and ground.
  >
• Is the resistance less than 5 ohms?

Yes
GO to B3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. B3 CHECK THE MULTI-FUNCTION SWITCH

• Key in OFF position.
• Disconnect: Multi-function Switch C202.
• Carry out the multi-function switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  
• Did the multi-function switch pass the component test?

Yes
GO to B4 .

No
INSTALL a new multi-function switch. REFER to Section 211-05 .

Sounds like the switch in the wiper motor has gone bad. You would have to replace the wiper motor to fix this problem. There are contacts inside the wiper motor head, when you turn them off it supplies power until the wipers return to the resting position and it opens the contact and then they stop. I hope you find this useful and helps you solve your issue.

Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

The wiper control module is probably at fault ,without test that is just a guess . The wiper/washer switch is a input to the wiper control module. Do you know anything about automotive electronics an electrical systems ?

• The Wipers are Inoperative

• Fuse.
• Wiper motor.
• Multi-function switch.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test B .

Voltage drop testing the power an ground circuits for the wiper control module would be a good place to start . Do you know how to test electrical circuits with a volt meter ?
PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

• Is the fuse OK?

Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.

• Is the voltage greater than 10 volts?

Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.

• Are the resistances less than 5 ohms?

Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .

• Is the multi-function switch OK?

Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).

• Is the resistance less than 5 ohms?

Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).

• Is the resistance less than 5 ohms?

Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).

• Is the voltage greater than 10 volts?

Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.

• Is the resistance less than 5 ohms?

Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.

there is a body control module behind the fuse box under the dash. it runs the wioers ,widows ,and locks,and much more

it sounds like you may need to replace you wiper motor