How to install idler on 1994 nissan quest part number 45008

Fuse 12 for the brake switch, but it covers a lot of other things as well that would be very noticeable.

Automatic Speed Control Device (ASCD) Brake Switch, Data Link Connector, Combination Meter, Heated Seat Relay, Park Neutral Position Switch, Display Unit, Steering Angle Sensor, Display Control Unit, Navi Control Unit, Back Door Control Unit, Sliding Door Control Unit RH/LH, Sonar Control Unit, Daytime Running Lights, Hands Free Telephone

Nissan Quest (V42; 2004-2009) fuses and relays

Fuse Box Diagrams https://fuse-box.info > nissan > nissan-quest-v42-2004...

Here you will find fuse box diagrams of Nissan Quest 2004, 2005, 2006, 2007, 2008 and 2009, get information about the location of the fuse panels inside the car ...

Missing: 1994 ‎' Show results with: 1994

possibly grounded or hot wire is ran with the running lights or park llights

1994 1998 Nissan Quest Service Repair Workshop Manual Download 1994 1995...

get your car fix right now

I just installed an after market radio in my 94 Quest.
The easiest way is to buy a Nissan Quest Radio Wiring Harness for Premium Sound. It will have the complete wire hookups. You can also hook up the blue wire from the new radio to thefactory (I think Blue or Blue/White) wire on the harness. That will turn the factory amp on.Hope this helps ,good luck

you need to solder front circuit board. I have posted info on this site if you search.

also go here

http://groups.yahoo.com/group/villagerquest/

I also repair for $25 (plus shipping) and your old control head if you can not solder yourself.

[email protected]

http://groups.yahoo.com/group/villagerquest/

Belt —A/C Removal

1. Remove the A/C compressor drive belt.
   1. Loosen the A/C compressor drive belt pulley tensioner bolt.
   1. Loosen the A/C compressor drive belt idler pulley adjustment bolt.

Installation

1. CAUTION: Incorrect drive belt installation will cause drive belt failure.
   NOTE: Inspect the pulleys for warping or abnormal wear.
   NOTE: Make sure drive belt is properly installed on each pulley.
   To install, reverse the removal procedure.
   • Adjust the A/C compressor drive belt. For additional information, refer to Belt Adjustment—A/C .

u don't have to remove the engine however you must remove the transmission and flywheel, you will also need the Nissan special tool to install the new full circle seal or it will leak.

if you leave the O/D off, what happens?

Go here and read files too.


http://autos.groups.yahoo.com/group/villagerquest/

go here for help
http://autos.groups.yahoo.com/group/villagerquest/files/


Item Part Number Description 1 — A/C Compressor Drive Belt Idler Pulley Adjustment Bolt (If equipped)
(Part of 8678) 2 — A/C Compressor Drive Belt Idler Pulley Tensioner Bolt (If equipped)
(Part of 8678) 3 8678 A/C Compressor Drive Belt Idler Pulley (If equipped) 4 8620 A/C Compressor Drive Belt (If equipped) 5 2E884 A/C Clutch Pulley (If equipped) 6 10346 Generator 7 10344 Generator Pulley 8 11719 Generator Adjustment Bolt 9 — Generator Locking Bolt 10 8620 Generator Drive Belt 11 6312 Crankshaft Pulley 12 — Water Pump and Power Steering Pump Drive Belt Adjustment Bolt (Part of 8678) 13 8678 Water Pump and Power Steering Pump Drive Belt Idler Pulley 14 — Water Pump and Power Steering Pump Drive Belt Idler Pulley Locknut (Part of 8678) 15 3A733 Power Steering Pump Pulley 16 8620 Water Pump and Power Steering Pump Drive Belt 17 8509 Water Pump Pulley A — Tighten to 16-20 Nm (12-15 Lb-Ft) B — Tighten to 33-37 Nm (24-28 Lb-Ft)

There is no easy way, water pumps are hard to change on this vehicle. Before starting the job I would buy a repair manual with step by step instructions. To give you some idea on how long it may take, the labor time is 4.5 hours for an experienced tech.