How many belts does it have - 1993 Nissan Pickup

BELT ROUTING DIAGRAM 1997 Mercury Sable 3.0L SFI 6cyl The Belt Routing Diagram

Fig. Fig. 16: Rotate the belt tensioner and...

Fig. Fig. 17: ... remove the belt from around one of the pulleys to remove the belt

WARNING Use caution when removing or installing the belt and make sure the tool does not slip from the drive belt tensioner or personal injury or damage to the belt tensioner and the belt may occur.

1. Attach a 15mm socket or wrench to the bolt attaching the tensioner pulley.
2. On all 3.0L (OHV) engines, rotate the drive belt tensioner clockwise to relieve belt tension and slide the belt off the pulleys.
3. On 3.0L (DOHC) engines, rotate the tensioner counterclockwise to relieve belt tension and slide the belt off the pulleys.

To install:

1. Install the drive belt on all the pulleys except the tensioner pulley.
2. Rotate the belt tensioner as outlined in the removal procedure to relieve belt tension and install the belt onto the tensioner pulley. Make sure the V-grooves make proper contact with the pulleys. Make sure the spring keeper releases or improper belt tension will occur.

drive belt.

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

you ask here. Please rate highly

SECTION 303-05: Accessory Drive 1998 Escort/Tracer Workshop Manual
REMOVAL AND INSTALLATION Belt -2.0L SPI Removal

1. Relieve the drive belt (8620) tension.
   • Use a (A) ratchet or breaker bar inserted in the square hole in the drive belt tensioner flange.
   • Rotate the (B) drive belt tensioner (6B209) in a clockwise motion to release belt tension.

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the engine splash shield.

1. Remove the drive belt from the accessory drive belt routing pulley (6C348) and then the remaining accessory pulleys.

Installation

1. Position the drive belt over the accessory pulleys. Raise and support the vehicle if necessary; refer to Section 100-02 .

1. Install the engine splash shield.

1. Rotate the drive belt tensioner in a clockwise motion.

1. Slip the drive belt under the belt idler pulley (8678) and release the tool. Remove the tool from the drive belt tensioner.

1. Accessory Drive-With A/C

1. Accessory Drive-Without A/C

---------------------------------------------------------------------------------------------------
Belt -2.0L Zetec Removal

1. Raise the vehicle on a hoist; refer to Section 100-02 .

1. Use a 13 mm wrench to rotate the drive belt tensioner (6B209) in a clockwise motion.

1. Remove the drive belt (8620).

Installation

1. Position the drive belt on all the pulleys and the drive belt tensioner.

Item Part Number Description 1 10300 Generator 2 19A216 Drive Belt Idler Pulley 3 3D673 Power Steering Pump Pulley 4 8509 Water Pump Pulley 5 6B209 Drive Belt Tensioner 6 19703 A/C Compressor 7 6316 Crankshaft 8 19A216 Drive Belt Idler Pulley 9 8620 Accessory Drive Belt

1. Rotate the drive belt tensioner in a clockwise motion.

1. Install the drive belt and gently release the drive belt tensioner.
   • Run the engine for several minutes to seat the belt into the pulley grooves.

ADJUSTING V-Belts Fig. 1: A gauge is recommended, but the belt deflection may be checked using light thumb pressure
Fig. 2: Loosening alternator pivot/adjustment bolt in order to tighten the belt Fig. 3: Apply tension to the belt being careful not to damage the case. While holding accessory in this position, tighten the pivot bolt. Fig. 4: Using a 1?2 in. ratchet, apply tension to the air conditioning belt while tightening the pivot bolt Belts are normally adjusted by loosening the bolts of the accessory being driven and moving that accessory on its pivot points until the proper tension is applied to the belt. The accessory is held in this position while the bolts are tightened. To determine proper belt tension, you can purchase a belt tension gauge or simply use the deflection method. To determine deflection, press inward on the belt at the mid-point of its longest straight run. The belt should deflect (move inward) 3?8 - 1?2 in. (10-13mm). A general rule for alternator belt tension is that the pulley should not be capable of being turned with hand pressure. Serpentine Belt On most newer vehicles, a single belt is used to drive all of the engine accessories formerly driven by multiple V-belts. The single belt is referred to as a serpentine belt. All the belt driven accessories are rigidly mounted with belt tension maintained by a spring loaded tensioner. Because of the belt tensioner, no adjustment is necessary. REMOVAL & INSTALLATION V-Belt Fig. 1: Loosen the component mounting and adjusting bolts slightly
Fig. 2: Remove the belt by pushing the component toward the engine
Fig. 3: Remove the drive belt
Fig. 4: To tighten the belt, pull the component away from the engine and tighten the mounting bolts to specifications
To remove a V-style drive belt, simply loosen the accessory being driven and move it on its pivot point to free the belt. Then, remove the belt. It is important to note that on engines with many driven accessories, several or all of the belts may have to be removed to get at the one to be replaced. Serpentine Belt Fig. 5: Serpentine belt tensioner - V6 engine
Fig. 6: Serpentine belt tensioner - V8 engine
A belt tensioner is used on these models, to maintain proper belt tension. To relieve belt tension, rotate the belt tensioner (using a 15mm socket) to relieve pressure on the belt. With tension relieved, the belt may then be removed from the engine. It is important to note the belt location at each pulley, to assure correct installation, and proper operation of the engine cooling system. A diagram may be helpful in denoting belt positioning. NOTE: Take care not to bend the tensioner when applying torque. Damage to the tensioner will occur. Maximum torque to load belt should not exceed 30 ft. lbs. (41 Nm).

Removal & Installation

1. Raise and support the vehicle.
   
2. Remove the engine splash shield.
   
3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
   
4. Remove the drive belt from the alternator.
   
5. Slowly release the drive belt tensioner.
   
6. Remove the drive belt from the accessory drive pulleys.
   

To install:

1. Install the drive belt to the accessory drive pulley.
   
2. Rotate the drive belt tensioner clockwise.
   
3. Install the drive belt to the alternator.
   
4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
   
5. Slowly release the drive belt tensioner
   
6. Install the engine splash shield.
   
7. Lower the vehicle.
   

Accessory drive belt routing—1.5L engine


Accessory drive belt routing—2.0L engines


Accessory drive belt routing—2.4L engines


Accessory drive belt routing—2.5L and 2.7L engines


Accessory drive belt routing—3.0L and 3.5L engine

2003 Hyundai Tiburon 2.7L MFI DOHC 6cyl

Inspection
Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.
Removal & Installation

1. Raise and support the vehicle.
2. Remove the engine splash shield.
3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
4. Remove the drive belt from the alternator.
5. Slowly release the drive belt tensioner.
6. Remove the drive belt from the accessory drive pulleys.

To install:

1. Install the drive belt to the accessory drive pulley.
2. Rotate the drive belt tensioner clockwise.
3. Install the drive belt to the alternator.
4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
5. Slowly release the drive belt tensioner
6. Install the engine splash shield.
7. Lower the vehicle.

Fig. Accessory drive belt routing-3.0L and 3.5L engine




Fig. Accessory drive belt routing-2.5L and 2.7L engines




Fig. Accessory drive belt routing-2.4L engines




Fig. Accessory drive belt routing-2.0L engines




Fig. Accessory drive belt routing-1.5L engine




Fig. Accessory drive belt routing-3.0L engine




Fig. Accessory drive belt routing-2.5L engines




Fig. Accessory drive belt routing-2.4L engines




Fig. Accessory drive belt routing-1.8L and 2.0L engines




Fig. Accessory drive belt routing-1.5L engine




Fig. Accessory drive belt routing-2.4L engines




Fig. Accessory drive belt routing-2.0L engines




Fig. Accessory drive belt routing-1.5L engine


I hope help you with this (remember rated this help) Good luck.

To Remove BELTS : Drive Belt :
Disconnect battery ground cable
Remove wheel and tire
Detach accessory drive belt
detention drive belt
detach accessory drive belt
Remove accessory drive belt
slacken the tensioner
remove accessory belt drive

Install in reverse order
WATER PUMP BELT : Remove battery tray
Remove water pump belt
De-tension water pump belt
Remove water pump belt

Installation in reverse
Hope this is helpfull

Drive Belt Replacement WARNING: IF EQUIPPED, DO NOT ALLOW DRIVE BELT TENSIONER (6B209) TO SNAP BACK AS DAMAGE TO DRIVE BELT TENSIONER OR PERSONAL INJURY COULD RESULT.
NOTE: Minor cracks in the V-grooved portion of the serpentine drive belt (8620) are considered normal and acceptable. If the drive belt has chunks missing from the ribs, the drive belt should be replaced.

NOTE: Conditions requiring drive belt replacement are excessive wear, rib chunk-out, severe glazing, frayed cords or other conditions. Replace any drive belt exhibiting any of these conditions.

NOTE: When installing drive belt on pulley, make sure that all V-grooves make proper contact with pulleys.





Drive Belt, Serpentine—Except SHO
Removal

1. WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP FROM DRIVE BELT TENSIONER OR PERSONAL INJURY AND/OR DAMAGE TO DRIVE BELT TENSIONER AND DRIVE BELT MAY OCCUR.
   Using a 15 mm socket or wrench on bolt attaching drive belt tensioner pulley, rotate drive belt tensioner clockwise on 3.0L (2V) and 3.0L (2V) FF, rotate the drive belt tensioner counter clockwise on 3.0L (4V) to remove drive belt from pulleys. Make sure spring keeper engages into slot.
   
   
   Drive Belt Tensioner—3.0L (4V)
   
   
   
   
   

Installation

1. Install drive belt over all pulleys (except drive belt tensioner).
   

1. Rotate drive belt tensioner as described under the removal procedure and install drive belt over drive belt tensioner pulley. Make sure that all V-grooves make proper contact with pulleys. Make sure spring keeper releases or improper belt tension will occur.
   
   
   Pulley, Routing—Accessory Drive Belt 3.0L (2V)/3.0L (2V) FF Engine
   
   
   
   
   
   Item Part Number Description 1 10300 Generator 2 6C348 Idler Pulley 3 3A674 Power Steering Pump 4 19703 A/C Compressor 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 8501 Water Pump 8 8620 Drive Belt
   
   Pulley, Routing—Accessory Drive Belt 3.0L (4V)
   
   
   
   
   
   Item Part Number Description 1 3A674 Power Steering Pump 2 8501 Water Pump 3 19703 A/C Compressor 4 8620 Drive Belt 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 10300 Generator

3.4L SHO Engine
Removal

1. Remove the right front wheel and tire assembly. For additional information, refer to Section 04-04.
   

1. Remove the inner fender splash shield.
   

1. Remove the alternator shield.
   

1. WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE WRENCH DOES NOT SLIP FROMDRIVE BELT TENSIONER OR POSSIBLE PERSONAL INJURY AND/OR DAMAGE TO DRIVE BELT TENSIONER AND DRIVE BELT MAY OCCUR.
   Using a 3/8 inch ratchet on the lifting lug, rotate drive belt tensioner counterclockwise (upward) and engage spring keeper. Remove drive belt from drive belt tensioner.
   

1. Lower vehicle.
   

1. Remove drive belt.
   

Installation

1. Install drive belt over all pulleys (except drive belt tensioner ).
   

1. Raise vehicle on hoist.
   

1. Rotate drive belt tensioner , as described under Removal procedure and install drive belt over drive belt tensioner pulley. Make sure all V-grooves make proper contact with pulleys. Make sure the spring keeper is released or improper belt tension will occur.
   

1. Install the alternator shield.
   

1. Install the inner fender splash shield.
   

1. Install the wheel and tire assembly. For additional information, refer to Section 04-04.
   
   
   Pulley Routing—Accessory Drive Belt, 3.4L SHO
   
   
   
   
   
   Item Part Number Description 1 3A733 Power Steering Pump Pulley 2 6B217 (RH) Idler Pulley 3 19703 A/C Compressor 4 8620 Drive Belt 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 10346 Generator 8 6B217 (LH) Idler Pulley 9 6B217 (Center) Idler Pulley

Drive Belt, Water Pump
Removal

1. NOTE: If removal of the water pump drive pulley is required, refer to Section 03-03.
   
   Rotate drive belt tensioner clockwise by hand and remove drive belt from drive belt tensioner .
   

1. Remove drive belt from water pump drive pulley and water pump pulley.
   

Installation

1. Position drive belt onto water pump drive pulley and water pump pulley.
   

1. Rotate drive belt tensioner clockwise by hand and install drive belt over top of drive belt tensioner pulley. Make sure all V-grooves make proper contact with pulleys.
   
   
   Pulley Routing—Water Pump Drive Belt
   
   
   
   
   
   Item Part Number Description 1 6B209 Drive Belt Tensioner 2 6A312 Crankshaft Pulley 3 8501 Water Pump 4 8620 Drive Belt

depends on the engine...3.3 has 1 belt
3.0 has 2 belts a serpentine belt and an ac belt
2.5 has 3belts a waterpump belt an ac belt and a power steering belt