2008 ford escape. removal of rear bumper cover

2008 Kia Sedona Bumper Covers

CarParts.com https://www.carparts.com > ... > 2008 > Bumper Cover

Get the best deals on an aftermarket 2008 Kia Sedona Bumper Cover. Lifetime Replacement Guarantee. Free 60-Day Returns. Order today!
"); background-repeat: repeat-x; display: inline-block; overflow: hidden; position: relative; background-size: 14px 11.4px; height: 11.4px; width: 68px;">"); background-repeat: repeat-x; display: block; background-size: 14px 11.4px; height: 11.4px; width: 70px;"> Rating: 4.8 · ‎10 votes · ‎US$101.99 to US$139.99

NEW Rear Bumper Cover for 2006-2014 Kia Sedona ...

Bumpers That Deliver https://bumpersthatdeliver.com > new-rear-bumper-co...

This replacement Rear Bumper Cover will help restore your vehicle's aesthetic value if you need to replace a scratched, dinged, or collision-damaged Rear Bumper ...
US$240.99

Rear Bumper Cover Repair procedures

Kia Sedona manuals https://www.kisedona.com > rear_bumper_cover_repa...

Take care not to bend or scratch the trim and panels. 1. Remove the rear combination lamp cover (A) using a screwdriver or remover.

To remove the rear bumper cover on a 2008 Nissan Quest, you can follow these general steps:

1. Prepare the Vehicle: Ensure that the vehicle is parked on a flat surface and the engine is turned off. Put on safety goggles and gloves to protect yourself during the removal process.
2. Locate the Fasteners: Look for the fasteners securing the rear bumper cover. They are typically located underneath the bumper cover, near the wheel wells, and along the bottom edge of the bumper.
3. Remove the Fasteners: Depending on the specific model and trim level, the fasteners may be screws, bolts, or plastic clips. Use the appropriate tools, such as a screwdriver or socket wrench, to remove the fasteners one by one. Turn them counterclockwise to loosen and remove them. Keep the fasteners in a safe place for reinstallation later.
4. Disconnect Electrical Connections (if applicable): If your Nissan Quest has any electrical connections, such as sensors or lighting, attached to the rear bumper cover, disconnect them carefully. Look for connectors near the edges or inside the trunk area. Gently detach the connectors by pressing the release tabs or using a flat-head screwdriver to release any locking mechanisms.
5. Release the Clips: Once the fasteners are removed, there may be plastic clips or tabs securing the bumper cover to the vehicle's body. Carefully pry or release these clips using a trim removal tool or a flat-head screwdriver. Take care not to damage the bumper cover or the vehicle's body.
6. Remove the Bumper Cover: With all the fasteners and clips released, gently pull or wiggle the rear bumper cover away from the vehicle's body. Start from one side and work your way to the other, ensuring that all connections and clips have been detached. Be cautious of any remaining electrical connections as you remove the bumper cover completely.

Please note that the exact steps and fastener locations may vary slightly depending on the specific trim level and optional features of your 2008 Nissan Quest. It's always recommended to consult the vehicle's owner's manual or a professional technician for more precise instructions tailored to your vehicle.
Take your time during the removal process to avoid any damage to the bumper cover or the vehicle's body. If you're unsure or uncomfortable performing the removal yourself, it's best to seek assistance from a qualified technician or a reputable automotive service center.

Hi Robert,

Please watch videos below and I'm sure it help you !!

https://www.youtube.com/watch?v=JTQLDfumlBw
https://www.carid.com/ford-sport-trac-rear-bumpers/

regards,
Sonu

FSm covers that
alldata.com ,log in and read like we do.?
remove skins, the unscrew bolts (obvious)

Looking under the car the oil filter is located just behind the front bumper, a little off to the passenger side. Should be one of the first things you see once you get past the bumper.
The link below has a very detailed step-by-step video of the entire oil change process, including locations of the oil drain plug and oil filter. Hope that helps.
2008 Ford Escape Oil Change - Detailed

Press the realese end pull upward on them at the same time,

Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Removal and Installation

1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
   Remove the front bumper cover. For additional information, refer to Section 501-19.

1. NOTE: Pull headlamp assembly forward to access electrical connectors.
   Remove the headlamp assembly.
   1. Remove the three bolts.
   1. Loosen the nut.
   • Disconnect the electrical connectors.

1. To install, reverse the removal procedure.
   • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..


Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
Removal and Installation
NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.

1. Remove the front bumper cover. For additional information, refer to Section 501-19.

1. Remove the 3 headlamp assembly bolts.
   • To install, tighten to 5 Nm (44 lb-in).

1. Remove the headlamp assembly nut and the headlamp assembly.
   • Disconnect the electrical connectors.
   • To install, tighten to 5 Nm (44 lb-in).

1. To install, reverse the removal procedure.