Question about 2001 Toyota 4Runner

1 Answer

Where is the intake manifold located at"? - 2001 Toyota 4Runner

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 406 Answers

It is the top of your motor where your throttle tube connects to the engine..it covers all six cylinders to get air to them...basicly there are three main parts of an engine..the block that holds the Pistons,the intake manifold on top and the exaust manifold on tne sides to allow Pistons to exaust..I hope this helps..if your looking to change replace gaskets..faily major job..good luck..

Posted on Feb 22, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Knock sensor diagram


On the 2.4 liter four-cylinder engine it is located on the siie of the engine block (the side nearest the firewall).

On the 3.0 Liter V-6 engine there are 2 knock sensors and the are located in the "valley" below the intake manifold. You'll have to remove the intake manifold to get to them.

Jul 22, 2014 | 2003 Toyota Camry

1 Answer

Location knock sensors 2000 toyota avalon xls 3.0 location


they are located under the intake manifold in the center of the engine. One is towards the front and one is towards the rear. The intake plenum and intake manifold will need to be removed in order to service the knock sensors. More commonly the harness fails.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Apr 02, 2013 | Toyota Avalon Cars & Trucks

2 Answers

Where is the starter located on a 96 bmw 328i


The starter is located under the intake manifold here's a pic with the manifold removed.

teflon434_0.jpg

To remove the starter there are 2 options remove the intake manifold or remove the transmission.

Apr 12, 2011 | 1999 BMW 328 Series

2 Answers

I need to find the intake air temperture sensor in my dodge


depends on the engine...
3.7 liter, #1 below:

jturcotte_112.jpg

4.7 liter:

jturcotte_113.jpg

5.7 liter, #2 below:

jturcotte_114.jpg

Jan 01, 2011 | 2006 Dodge Ram 1500

1 Answer

Check engine light came on diagnostic said it was throttle position sensor i need to find out where it is located so i can replace it


The throttle position sensor is located between the air filter box and the intake manifold. If you aren't familiar with engines, the air filter box is usually located behind the driver's side headlight. There is a rubber tunnel that runs from the air box to the intake manifold. Between the rubber tunnel and the intake manifold you will find the throttle bolted to the intake manifold. The sensor is located on the throttle.

Jan 03, 2010 | 2005 Chevrolet Cobalt

2 Answers

Spark plug location in a 2001 ford escape


Need to remove upper intake manifold to reach valve cover close to firewall.
1) The location of spark plugs 456 are under the plastic shield in front of the engine. It takes an 8mm socket to remove the three bolts holding the shield once the shield is removed you will see a coil for each spark plug. Use the 8mm socket and remove the coil and rubber boots. You will now see the spark plug (note there are not any spark plug wires).
2) The location of spark plugs 123 are located to the rear of the eng. You have to remove the air intake manifold in order to get to the spark plus. Remove the throttle wire then remove the other items on top of the intake manifold.

Nov 16, 2009 | 2001 Ford Escape

4 Answers

Where is knock sensor located on 2001 silverado 6000 engine


Under the intake manifold. Make sure you get the harness for the knock sensors. and clean out all of the rust and junk you're going to find donw in the holes before and after you replace the sensors.

Nov 01, 2009 | 2005 Chevrolet Silverado

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

2 Answers

1998 kia sephia starter


Its located just under the intake manifold. you will need to remove the exhaust pipe to access it. there is also an upper and lower intake manifold support bracket that will need to be removed as well to extract the starter.

Its in a tough spot.

Jun 17, 2009 | 1998 Kia Sephia

1 Answer

Need location


The PCV valve for a 5.0L is located below the upper intake manifold in the rear. It is locate in the lower intake manifold in the rear right below the upper intake manifold. It is really hard to see but if you get a mirror you can probably see it.

Apr 12, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
2001 Toyota 4Runner Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...