How do I remove a headlight assembly on a Renault Scenic 2005

Question edited for clarity.
Question moved to sub category.

There are fuse boxes all over the place!

Lights wiring and lighting issues
https://www.google.com/search?q=2006+renault+scenic+1.6+lights+wiring+diagram

Fuse box diagram Renault Scenic 2 and relay with ...

https://fuseandrelay.com > renault > scenic-2
We will show you where the relay and fuse boxes are located in the Renault Scenic 2 generation. We will provide photos of boxes, diagrams and describe the ...
Feb 14, 2022 · Uploaded by Fuse and relay
‎Passenger compartment · ‎Fuse box · ‎Box under the passenger seat

2004-2009 Renault Grand Scenic Fuse Box Diagram

https://knigaproavto.ru > shemy > 378-20042009-renau...
Sept 5, 2017 - Fuse Box Diagram Renault Grand Scenic (2004, 2005, 2006, 2007, 2008, 2009)

Get flat screwdriver and star screwdriver

menu

How to Adjust a Headlamp Beam on a 2005 Chevrolet Cavalier...

When you replace the headlamp assembly in the 2005 Chevrolet Cavalier, you must also adjust the headlamp beams. Like most vehicles, there are two screws located on the headlamp assembly that control the vertical and horizontal direction of the headlamps. Proper adjustment is necessary for adequate visibility during nighttime driving; bad adjustment can make it difficult for you to see or make it difficult for oncoming drivers to see, creating a potentially dangerous situation. You can adjust the headlamp beams yourself with a screwdriver in about 15 minutes.
Park the Chevrolet Cavalier on a flat surface facing a wall or garage door approximately 15 feet away. Park the Car so that it is perpendicular to the wall.

Lift the hood and remove the plastic trim panel above each of the headlights. There are three plastic fasteners that secure the trim panel; pry the fasteners out using a flathead screwdriver. Lift the trim panel up to remove. There are two adjusting screws beneath the trim panel, one on the top of the headlamp assembly and one along the outer side of the headlamp assembly.

Turn the headlights on so that they shine on the wall. Ensure the headlights are on the "dim" setting.

Adjust the vertical bolt, located on the top of the headlight assembly near the center of the vehicle to raise or lower the headlight, using a crosspoint screwdriver. Turn the screw counterclockwise to lower the headlamp beam; turn the screw clockwise to raise the headlamp beam. Adjust the headlamp so that the beam is below a driver's eye level.

Adjust the horizontal bolt, located on the outer side of the headlamp assembly to move the headlamp beam right of left, using a crosspoint screwdriver. Turn the screw counterclockwise to move the headlamp beam right; turn the screw clockwise to turn the beam left. Adjust the headlamp so that the beam shines straight ahead or slightly toward the center of the vehicle.

Replace the plastic trim panel and fasteners and close the hood. Warning: raising the lights too high can make it difficult for other drivers to see you.

to replace headlight bulbs turn steering so you can open flap in the wheel arch.open flap liner to access of the rear headlight unit.to remove inner bulb in headlight housing remove the air intake duct at front of the air cleaner housing right hand side unclip the wiring harness connector unclip the the left wiring harness connector front of fuse and relay.to remove the dipped beam remove the plastic cover from rear of head light unit.through wheel flap opening. rotate bulbholder anti clockwise to remove bayonet fitting remove headlight bulb. WARNING WEAR CLEAN GLOVES WHEN HANDLING HEADLIGHT HALOGEN BULBS OILS FROM HANDS WILL CAUSE HALOGEN BULB TO OVERHEAT AND BLOW OUT.

Its Pretty easy see instructions below



REMOVAL PROCEDURE

1. Open and support the hood.
2. Remove the grille.
3. Pull up on the retaining tabs (1) in order to remove the headlamp assembly from the headlamp panel.
4. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
5. Disconnect the headlamp electrical connector (2) from the headlamp assembly.
6. Remove the side marker socket (4) from the headlamp assembly.
7. Remove the park/turn socket (3) from the headlamp assembly.
8. Remove the headlamp assembly from the headlamp panel.

INSTALLATION PROCEDURE

1. Position the headlamp assembly to the headlamp panel.
2. Index and seat the tabs on the park/turn socket (3) to the headlamp assembly.
3. Index and seat the tabs on the side marker socket (4) to the headlamp assembly.
4. Connect the headlamp electrical connector (2).
5. Connect the headlamp leveling electrical connector to the motor/actuator if equipped.
6. Align and install the 4 locator pins on the back of the headlamp assembly into the retaining tab holes.
7. Push down on the retaining tabs (1) in order to lock the headlamp assembly into the headlamp panel.
8. Install the grille

Headlamp Removal & Installation Bulb Replacement To Remove:

1. Remove the Headlamp Assembly. Headlamp bulbs
   
   
2. Turn the high/low beam bulb socket counterclockwise to remove.

To Install:

1. Turn the high/low beam bulb socket clockwise to install.
2. Install the Headlamp Assembly.

Headlamp Assembly (Park, Turn, Cornering and Side Marker Lamps) To Remove:
Headlamp assembly R &I

1. Rotate the headlamp assembly retainer pins and pull up to remove.
2. Remove the mounting bolts.
3. Disconnect the harness connectors.

To Install:

1. Connect the harness connectors.
2. Position the headlamp assembly on the panel.
3. Rotate the retainer pins and push down to lock in place.
4. Install and secure the mounting bolts.

ok you have removed the bolt and the retaining pin
now pull the light foward to disengage the ball and socket attachment at the rear of the headlamp

Are u sure that the bulbs are OK? I had no dipped lights on mine, & thought it must be a fuse or another electrical fault. It turned out, both bulbs had gone. I think this often happens when one side goes, the other soon follows.

If the headlights do no ilinitate when switched on you have a faulty battery or cable conection problem.Jiggle the cables while the headlamps are switched on if they do not lightr up:battery failure.If they do,clean up the connections at the cable to battery and put the on securely

under the hood, near the rear of the headlamp assemblies, there are adjustment screws with phillips head screwdriver slots. They may be hard to see with the radiator support above the headlamps, but they will be the only phillips adjustment screw heads on the whole headlamp assembly. They will be facing directly vertical facing up

ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..


Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
Removal and Installation
NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.

1. Remove the front bumper cover. For additional information, refer to Section 501-19.

1. Remove the 3 headlamp assembly bolts.
   • To install, tighten to 5 Nm (44 lb-in).

1. Remove the headlamp assembly nut and the headlamp assembly.
   • Disconnect the electrical connectors.
   • To install, tighten to 5 Nm (44 lb-in).

1. To install, reverse the removal procedure.