What wire in a 2007 sebring would short out if the break lights stop working?

Have changed relay brake switch 3 times

Jeremy W. Feb 19, 2015

Hi beverly , I want to help you with your question, but I need more information from you. Can you please add details in the comment box? Have you checked the fuse? Power to the switch?

5 Related Answers

honeymokey

3113 Answers
Posted on Jul 02, 2009

SOURCE: oil light on while driving 2002 Sebring

2.7 ? This motor has oil problems if not changed every 3000 miles. Put a chrysler filter on it and the correct weight of oil, never use a fram oil filter.

Anonymous

1 Answer
Posted on Sep 06, 2009

SOURCE: How do i change the left brake light for a 2007

how do i get the brake light out of my 2007 Chrysler sebring????

Anonymous

2317 Answers
Posted on Oct 18, 2010

SOURCE: Hello! I am going to replace my front brake pads

Normally it's not too tough to change the brake pads with minimal tools. You will need a large C clamp or brake tool to compress the brake caliper piston back into the caliper. I would check the condition of the brake rotors, if you have heard some scraping.

Justin Fitzgerald

543 Answers
Posted on Apr 24, 2011

SOURCE: cannot disconnect electrical cable from

those can be finicky when they get dirt in them, the best way to disconnect them is to remove the red clip entirely and then using a small screw driver insert it into the connecter and push the locking part in an upward direction (ie. away from the connector) and pull at the same time.

Zim.

Anonymous

6 Answers
Posted on May 02, 2011

SOURCE: 2007 sebring brake light

Replace it? Not sure if this was suppose to be posted here or som th ng missing

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1helpful

1answer

Does the relay that is connected to the turn signal switch on top of the steering column have any thing to do with the break lights. On a 2001 sebring convertibe

No , the turn / hazard flasher has nothing to do with the brake lights . The brake lamp switch on top of the brake pedal arm , fuse # 11 20 amp located in the under hood fuse box an wiring an the bulbs . are all that control the brake lights .Do know what a wiring diagram is ? How to use a DMM - digital multi - meter to test electrical circuits ? Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size. Under system click on lighting ,then under subsystem click on exterior lighting . Click the search button , then click the second blue link , the first diagram is for the brake lights electrical circuit . Watch these videos on automotive electrical testing .
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts
Electric Testing Techniques You Need to Know

Read full answer

Mar 22, 2018 • Cars & Trucks

0helpful

2answers

Brake lights dont turn on toyota rav 4, whats the problem?

Check the switch on the break peddle , thay can work loose or renewal good luck colin

Read full answer

Jul 05, 2017 • Toyota Cars & Trucks

1helpful

1answer

2007 Chrysler Sebring base. Brake lights both do not work. Replaced brake light switch, made certain to follow steps completely. I've done so three times thinking I may have done it wrong.

does ur third brake light work??if not i would see if maybe u had a broken wire at ur brakelite switch. very possible with all the constant moving of pedal..also plz make sure bulbs are good. i have seen both side blown .hope this helps

Read full answer

Jun 28, 2015 • Chrysler Cars & Trucks

0helpful

2answers

I have a 2007 Yukon denali xl. the rear rt break light doesn't work. it doesnt illuminate when braking. it does illuminate when parked. bulb has been replaced and changed with the left side to make sure it...

Dodgy connection somewhere but where ?? is the million dollar question,Does this vehicle have the illegal funny light system where the stop light is the indicator as well or is it on the europeon system with a seperate indicator light

Read full answer

Feb 02, 2015 • 2007 GMC Yukon Denali

0helpful

1answer

On the 1997 Chrysler Town & Country LX, 3.3Litre, the tail lights don't work. The break lights work, the turn signal works also. It's not the light bulb.

All three of your lights on the rear are ran separately. The tail lights are ran with headlight switch the brake lights off the break sensor the turn signals are ran from arm switch and then there are relays as well. Electrical issues are a real pain to track. However that's not abnormal have 2 of the 3 working when theres a bad relay or short in the wire

Read full answer

Oct 07, 2014 • 1997 Chrysler Town & Country

0helpful

1answer

2004 chrysler sebring. my break lights don't come on when i hit the break pedal.

There is a brake light switch on the pedal inside the cabin of the car, if this switch is bad your lights will not work, also I'm fairly confident that the Sebring has a seperate fuse for the brake lights, check your fuse panels also

Read full answer

Apr 02, 2013 • Cars & Trucks

1helpful

1answer

Tail lights, stop lights,dash lights and turn lights won't work. Was OK then stopped. Don't see any fuses for them. What happened and how do I fix the problem? Have a 1967 Galaxie hardtop that I have...

lets break down the symtoms
BRAKE LAMPS
brake lamp stop switch should be powered at all times
locate stop lamp switch ( should be 2 prong Switch located on brake pedel assembly)
jumper 2 prongs together with paperclip
do brake lamps come on? if not
check fusable links (wires that are ment to melt if a short occures)
located on supply side of starter soleniod under hood near battery on inner fender.
if melted you must locate and repair short prior to replacing the fusible link

PLease rate this responce

Read full answer

Jul 29, 2010 • Ford Crown Victoria Cars & Trucks

1helpful

1answer

2007 nissan quest, brake lights have stopped working. can you tell me which fuse controls it...

how about criuse control it also not working you may have bad switch 3 wire switch at brake pedal are harder to diagnos 2 wire one wire has power till you press the pedal most all cars brake light is fusible link or special fuse for it is on all the time. If no pwr even with key off at the brake switch key on or off on any wires then you may need to find pwr. to the system , Note if any fuses are burnt repalce them same type if that fixes something yeah but it also may return .

Read full answer

Jan 03, 2010 • 2007 Nissan Quest 3.5 Minivan

1helpful

1answer

I have a Ford Fiesta 2007 1.4 TDCI. When I brake

Check the wiring harness. Sounds like it has come in contact with the break assembly and is shorting out. Look for exposed wiring where the cover has worn off coming in contact with the break. Tape all exposed wiring and be glad you haven't had a small fire.

Read full answer

Sep 17, 2009 • 2007 Ford Focus (3 Door) Hatchback

0helpful

2answers

Break / hazard light fuses keep blowing

check both brake lights for moisture getting into them.

Read full answer

May 25, 2008 • 1999 Cadillac Escalade

Not finding what you are looking for?

View Most Popular

2007 Sebring Sedan

Cars & Trucks

Does the relay that is connected to the turn signal switch on top of the steering column have any thing to do with the break lights. On a 2001 sebring convertibe

Cars & Trucks

109 views

Ask a Question

Usually answered in minutes!

Have a manual for 2007 Chrysler Sebring Sedan? Or just drag it here!

Related Topics:

What wire in a 2007 sebring would short out if the break lights stop working?

5 Related Answers

honeymokey

Anonymous

Anonymous

Justin Fitzgerald

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Does the relay that is connected to the turn signal switch on top of the steering column have any thing to do with the break lights. On a 2001 sebring convertibe

Brake lights dont turn on toyota rav 4, whats the problem?

2007 Chrysler Sebring base. Brake lights both do not work. Replaced brake light switch, made certain to follow steps completely. I've done so three times thinking I may have done it wrong.

I have a 2007 Yukon denali xl. the rear rt break light doesn't work. it doesnt illuminate when braking. it does illuminate when parked. bulb has been replaced and changed with the left side to make sure it...

On the 1997 Chrysler Town & Country LX, 3.3Litre, the tail lights don't work. The break lights work, the turn signal works also. It's not the light bulb.

2004 chrysler sebring. my break lights don't come on when i hit the break pedal.

Tail lights, stop lights,dash lights and turn lights won't work. Was OK then stopped. Don't see any fuses for them. What happened and how do I fix the problem? Have a 1967 Galaxie hardtop that I have...

2007 nissan quest, brake lights have stopped working. can you tell me which fuse controls it...

I have a Ford Fiesta 2007 1.4 TDCI. When I brake

Break / hazard light fuses keep blowing

Not finding what you are looking for?

2007 Sebring Sedan

Does the relay that is connected to the turn signal switch on top of the steering column have any thing to do with the break lights. On a 2001 sebring convertibe

Ask a Question

Check Out the Latest Top Trucks Report!

Top Chrysler Experts

ZJ Limited

Ronny Bennett Sr.

Thomas Perkins

Are you a Chrysler Expert? Answer questions, earn points and help others

Manuals & User Guides

. 2007 Sebring Sedan Manual

Related Topics:

What wire in a 2007 sebring would short out if the break lights stop working?

5 Related Answers

honeymokey

Anonymous

Anonymous

Justin Fitzgerald

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Does the relay that is connected to the turn signal switch on top of the steering column have any thing to do with the break lights. On a 2001 sebring convertibe

Brake lights dont turn on toyota rav 4, whats the problem?

2007 Chrysler Sebring base. Brake lights both do not work. Replaced brake light switch, made certain to follow steps completely. I've done so three times thinking I may have done it wrong.

I have a 2007 Yukon denali xl. the rear rt break light doesn't work. it doesnt illuminate when braking. it does illuminate when parked. bulb has been replaced and changed with the left side to make sure it...

On the 1997 Chrysler Town & Country LX, 3.3Litre, the tail lights don't work. The break lights work, the turn signal works also. It's not the light bulb.

2004 chrysler sebring. my break lights don't come on when i hit the break pedal.

Tail lights, stop lights,dash lights and turn lights won't work. Was OK then stopped. Don't see any fuses for them. What happened and how do I fix the problem? Have a 1967 Galaxie hardtop that I have...

2007 nissan quest, brake lights have stopped working. can you tell me which fuse controls it...

I have a Ford Fiesta 2007 1.4 TDCI. When I brake

Break / hazard light fuses keep blowing

Not finding what you are looking for?

2007 Sebring Sedan

Does the relay that is connected to the turn signal switch on top of the steering column have any thing to do with the break lights. On a 2001 sebring convertibe

Ask a Question

Popular Questions

2012 chrysler 200 serpentine belt diagram

My electronic throttle control warning light came

COMO PONER LA CADENA DE

CODES,P0442,P0455,P0456,P1684

Car Won't Fully Shift into Park

Check Out the Latest Top Trucks Report!

Top Chrysler Experts

ZJ Limited

Ronny Bennett Sr.

Thomas Perkins

Are you a Chrysler Expert? Answer questions, earn points and help others

Manuals & User Guides

. 2007 Sebring Sedan Manual