How do I install a paramount restyling 51-0014 rear bumper on a 1997 Jeep Wrangler

SOURCE: 1997 Jeep wrangler

Clock spring mech is prob bad, first easy check is remove airbag 2 8mm bolt from back side of wheel make sure wires are still connected if they are good the clock spring mech is bad you can use a steering wheel puller to remove wheel and clock spring mech just snaps out and has 2 plugs on it, I have 2 if you need one.

SOURCE: 1991 jeep wrangler gas leak

Hello everyone,l

For those of you who haven't started removing the gas tank, I'll start from the beginning.
You will need a 1/2" socket, ratchet, extensions, flat head, needle nose, floor jack, rag, broomstick,. A creeper will make this easier. Depending on your dimensions and the height of the frame on your particular vehicle, you may be able to use it without jacking the vehicle up..

• Disconnect the negative battery terminal
• If your engine is fuel injected, you need to relieve the line pressure. This is done from the injector rack on top of the engine. About the center of the rack you will find what looks like a filler valve on your tire, only thicker. The fuel line can maintain over 40 P.S.I. pressure even with key off. Place a rag over the pressure relief valve. Use the corner of a screwdriver to poke the center core through the rag. A second or two should do it.
  
• Place a floor jack under the gas tank shield, jack it up until snug.
• Disconnect the rear exhaust hanger.
• Loosen and remove the three shield nuts above the rear end
  
• Remove the plastic shield from beneath the left rear corner. Two plastic anchors hold it on. Disengage them by pulling the center plug out about 1/2". This will expose the hoses connecting the tank to the body.
  
• Loosen the hose clamps
  
• If you can get them to twist, try and get them off.
  
• Rear nuts next. Loosen and remove all but the center one.
• Make sure the jack is centered and snug
  
• Remove the last nut. The tank isn't going to DROP. It will kind of lean, and jam against the exhaust.
• Insert the broom stick into the exhaust pipe.
• Push and hold it to the right, slowly let the jack down. Stop if it hangs up and work it free.
• When its down far enough to access the top of the tank, disconnect the plug, loosen thew hose clamps, remove the hoses, separate the vent hoses at the 'T' connector.
• Lower it the rest of the way
• The tank can now be separated from the shield.

SOURCE: how to replace a jeep tj fuel tank?

I would be really careful with doing this repair as this is very dangerous. You need to relieve the fuel pressure by pulling the fuel pump fuse and starting the truck. Drain the tank with a siphon pump. Remove any exhaust or other parts that are in the way, loosen the straps and support the tank with a floor jack and a block of wood. There are several hoses, and a few wire connectors to disconnect and you may want to replace those hoses while you're down there. Once you put the new tank in, reconnect the electrical and hoses, raise the tank and strap it back up. Put anything else back together you took off the truck.
Personally, I would take this in to get fixed as this is dangerous work (I did mention that). I you do this anyway, use your head and buy a proper container to hold the gas in , as well as jackstands and a class "B" fire extinguisher. Disconnect the battery and don't smoke or use a drop light under the car, and I will not accept responsibility for this.

SOURCE: Jeep wrangler Fuse box

You have two locations for the fuse box. One is either under the hood or behind the glove box. I would pull apart the glove box and take a look.

SOURCE: remove 2007 jeep compass bumper cover

Hello, I can assist you. Begin by rounding up the necessary tools:

7mm socket and ratchet
7mm wrench
10mm socket
screw driver or panel removal tool (for push rivets)
Now go to the following site and take a look at the step by step instructions and pictures which does a nice job of explaining this entire job. Thanks for using Fixya!
http://www.jeeppatriot.com/forum/showthread.php?t=6291