Where is the fuse box for the wipers

It is under the dash panel right hand side , kick panel ? Fuse F1.1 10amp . an fuse F1.113 30 amp.
Visual Inspection Chart Mechanical Electrical

• Windshield washer hoses
• Wiper linkage
• Multifunction switch

• CJB fuses:
  • 1 (10A)
  • 38 (25A)
  • 113 (30A)
• Circuitry
• Windshield wiper motor

• The windshield wipers are inoperative

• Multifunction switch.
• Circuitry.
• Ignition switch.
• Windshield wiper motor.

• Go To Pinpoint Test A .

PINPOINT TEST A: THE WINDSHIELD WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 1002 (BK/PK) FOR VOLTAGE

• Key in OFF position.
• Disconnect: Windshield Wiper Motor C125.
• Key in ON position.
• Measure the voltage between windshield wiper C125 pin 5, circuit 65 (DG), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 1002 (BK/PK), harness side and ground.
  
• Are the voltages greater than 10 volts?

Yes
GO to A2 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 875 (BK/LB) FOR OPENS

• Key in OFF position.
• Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 875 (BK/LB), harness side and ground.
  
• Are the resistances less than 5 ohms?

Yes
GO to A3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH

• Disconnect: Multifunction Switch C202a.
• Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  
• Did the multifunction switch pass the component test?

Yes
GO to A4 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR OPEN

• Measure the resistance between C202a pin 4, circuit 57 (BK), harness side and ground.
• Is the resistance less than 5 ohms?

Yes
GO to A5 .

No
REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS

• Using the following table, measure the resistance between the multifunction switch C202a harness side and the windshield wiper motor C125 harness side:
  
  Multifunction Switch C202a Windshield Wiper Motor C125 pin 7, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 5, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 1, circuit 63 (RD) pin 9, circuitwhere is the fuse box for the wipers - s3j~tr~en~file=a0045221.gif~gen~ref.gifr>
• Is the resistance less than 5 ohms?

Yes
GO to A6 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION

• Disconnect all wiper motor connectors.
• Check for:
  • corrosion
  • pushed-out pins
• Connect all wiper motor connectors and make sure they seat correctly.
• Operate the system and verify the concern is still present.
• Is the concern still present?

Yes
GO to A7 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR

• Key in OFF position.
• Disconnect: Windshield Wiper Motor C125.
• Carry out the windshield wiper motor component test as described in this section.
• Did the windshield wiper motor pass the component test?

Yes
The system is operating correctly at this time. Concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section. Hope this helps !

Fuse box is underneath the dashboard on the driver side down on the side.