My low beam headlights on my 2004 lexus rx330 are too high they blind onlooking traffc

unless they are seperate,you dont,if they are seperate,there is a screw on the bottom and side from the front that you can turn

Moe likely a bad earth for one of the lights as one light is working through another causing one to stop working

HEADLIGHTS NOT WORKING

It can be faulty headlight switch or issue with its wiring. Or its faulty head light fuse.

==========

To troubleshoot the issue i suggest you few help links with appropriate solution. So you can follow the test and confirm what exact problem is there in your case of headlights not working:-----

Click the link below: -----

All headlights not working?

http://repairhelpcenter.blogspot.com/2012/01/all-headlights-not-working.html

----------

• Working of Headlight switch?
------------
• Both headlight bulbs blow together?

------------
• Car headlight bulbs don't last long?

---------------

2007 Dodge Caliber: Low Beam Headlight Not working

http://technoanswers.blogspot.in/2012/06/2007-dodge-caliber-low-beam-headlight.html

----------

2003 Toyota Camry: Headlights Work Intermittently?

http://technoanswers.blogspot.in/2012/04/2003-toyota-camry-headlights-work.html

----------

Chevy Tahoe: Low Beam Lamps are not working?

http://technoanswers.blogspot.in/2012/04/chevy-tahoe-low-beam-lamps-are-not.html

----------

2001 Chevrolet Tahoe: Headlights not coming ON?

http://technoanswers.blogspot.in/2012/04/2001-chevrolet-tahoe-headlights-not.html

--------

2004 Dodge Ram: High Beam Light is DIM?

http://technoanswers.blogspot.in/2012/04/2004-dodge-ram-high-beam-light-is-dim.html

----------

2001 Chevrolet Tahoe: Both Low Beam Lamps Not Working?

http://technoanswers.blogspot.in/2012/04/2001-chevrolet-tahoe-both-low-beam.html

------------

Low beam headlights Modification?

http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html

---------
How to Replace a Headlight

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

------------
How to Replace a Headlight Bulb

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

-----------
How to Replace a Headlight Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

----------
How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html

How to Replace a Park Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

-----------

Low beam headlights Modification?

http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html

----------

Headlight Assembly Removal On Honda Accord

http://technoanswers.blogspot.in/2012/06/headlight-assembly-removal-on-honda.html

---------------

Honda Headlight Assembly Removal
http://schematicsdiagram.blogspot.in/2012/06/honda-headlight-assembly-removal.html

-----------

How to Replace a Headlight Door

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

----------

How to replace HID headlight bulbs for lexus 400h?

http://schematicsdiagram.blogspot.com/2012/01/how-to-replace-hid-headlight-bulbs-for.html

----------------

These will help.

Thanks.

Did the low beams go off?.. If not, it sounds like you have a bad switch.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Shine your head lights on a wall either in your garage or outside wall and re-adjust your head light back to were you think you had them last. Use the high beam and the low beam settings and you will be able to beam the light were you think they should be. Common problem with most new vehicles now days, low beams don't seem to be bright enough.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

You headlight lamp have a diffuser mechanism which allows it to flip between the hight beam and low beam feature of the bulb. In fact, you high beam will function even if the low beam is not working.

I would recommend the purchase of the new headlight lamp. It would cost you you any where from $15.00 per unit to get a replacement lamp