There are two cable that go to the door handle from the lock actuator. A block one and a grey one. The black one is slightly longer than the grey one. Which one goes to the door handle and which one goes to the lock switch? And inside the lock actuator, which cable goes at the top and which one goes at the bottom. I know I should have drawn a diagram when I took them off, but I'm an fool, OK?
SOURCE: 2003 Hyundai Tiburon Door Lock Problem
I had both doors with the same problem. I replaced the actuators and everything works perfect now.
SOURCE: hyundai accent '02 inside door handle & Lock removal
Removing the door is very tricky, trust me on this. I ended up breaking it the first time, so please learn from my mistake.
1. Remove all visible screws: 2 at bottom of door, 3 on front near
hinge, 1 on inside the door lever. You will need an average size
phillips screwdriver to do this.
2. On the door handle itself, you will see two circles. Pop the front
one out. You will need a LARGE size phillips screwdriver to do this.
3. Once screws are removed, take a (standard) flat-head screwdriver,
preferable one with a large face, and pry the triangular piece of
plastic (that covers the outside SIDE mirror) off. This will aide in
puting the door panel back on...TRUST ME!!!
4. Take the same flat-head screwdriver, and pry behind the door lock
(at the same time, push forward toward the door hinge). The assembly
should pop out.
5. Gently pry the door panel from the door, making sure not to break
any unnecessary pieces along the way. The door panel should be hanging
by the window sill opening.
6. This is where it will get tricky. It is advised that you use help
with this part: Angle the door panel at a 45 degree angle. AT THE SAME
TIME, slightly bend and twist the door lock handle until it fits
through the hole. You will see the 3 pegs the held it in the door from
before. Also note: Be careful not to break the 2 poles that are
attached to the lock.
7. After popping the lock through the hole, you should be able to lift
the door upward, and off the sill. Repeat these steps in reverse order
to re-attach door panel.
Be careful not to rip sound-deadening paper found on inside of door
unless you intend to remove or replace it! Not only does it prevent
dirt and moisture from entering your door (and possible rusting it from
the inside out), but it makes your speakers sound better too!
-SportTunerFreak
**It is also recommended to put a tiny bead of silicone on the inside
of the door panel to help suppress any rattling, and prevent moisture
and dust from entering. It also helps your screws obtain a tighter fit.
Hope this helps!
SOURCE: 2006 Ford Fusion inside door handle stopped working
The plastic door handle is broken.
You will need to get a replacement door handle.
Go to http://www.flickr.com/photos/gtppilot/sets...57607539089979/
This should help. It is a set of photographs and instructions to do the job of replacing the handle.
Good luck.
Rgrdrake
SOURCE: central locking on megane 2000
is yours the renault keycard to start and open doors?if it is a know these cards can go faulty.they were bad on renault laguna.the switch breaks off the board inside card.can be soldered back on.think you can get replacement switch kit on ebay with instructions how to fix.need someone who can solder with some eletronics knowhow.if not not sure sorry
SOURCE: how to adjust handbrake on hyundai excel 95, fix inside front doo
Adjusting the handbrake is easy.Between the two front seats where the cup holders are behind there is a cubby hole.This has a bottom which can be easily prised out.You will see the handbrake adjusters which you just need to tighten.
Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation
Door Lock Switch
Door Lock Diagnosis & Testing
Fig. Removing door lock actuator
Fig. Removing door lock motor-Sedan
60 views
Usually answered in minutes!
×