How to change modes in trip meter of swift car?

I believe it might be in manual also. Here is instructions.
Switch the display to the trip meter "A"
Turn the "POWER"switch off.
(If you have push button start)
While pressing the trip meter reset button turn the "POWER" switch to ON mode (press power button 2 times, foot off the brake).
Continue to press and hold the button until the trip meter displays "000000"and the multi-information display indicates that the reset is complete. or you here a beep.

replace it, its bad.
( as speedo shop can fix it at 2 times new. ?)

Hi there:

Turn the "Engine Start Stop" switch OFF with the trip meter A reading shown.

While pressing the trip meter reset button, set the "Engine Start Stop" switch to the Ignition ON mode. Continue to press and hold the button until the trip meter displays 000000.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Duplicate post

Hello. Welcome to FixYa. Please allow us to assist you.

This is really easy! Follow these directions:

Turn the key ON

Look at the odometer, and verify that it displays "ODO" and the total mileage traveled. If it is on "Trip A" or "Trip B", press the black stick next to the odometer to read "ODO", and the total miles traveled.

Turn the key OFF.

Press in, and HOLD the black trip meter reset button, hold it in.
DO not release it.

Turn the key ON (do not turn the key to Start)

Observe the Odometer display. The total mileage traveled will disappear, and you will see 5 dashes, then 4, then 3, then 2, then 1 dash, and finally, 5 zeros. Then, the total mileage traveled will redisplay.

Release the black trip meter reset stick.

This completes the reset procedure, and it will be back on in 5,000 miles, to remind you of you next oil change
.
NOTE: Newer cars have a slightly different procedure. The reset procedure starts on the "TRIP A" setting, as opposed to the "ODO" setting. Depending on the year of your car, one or the other will work.

Hope this helps!

Ensure all doors are closed.Turn ignition key to position 1.Press and hold reset button on a dashboard left hand side down/instrument panel/.Immediately turn ign.key to position 2.Keep reset button depresed until trip meter is reset to 0. NOTE:IF trip meter has already been reset.Hold reset button for 10-14 secondsuntil previous trip meter reading is shown.Press and hold reset button until trip meter is reset to 0 ;;;; Release a button within 4 secondsThere will be an audible signal When reset complete.

lol, push the button and hold it in for a second

Look in your owners manual and go to the part that explains the different symbols on your dash. Look for that service reminder and it should tell you what page to go to to learn more about that. Somewhere there should be some wording to the effect that "When you have your car serviced by a certified Toyota dealer they will reset it for you. In the event that someone other does your maintenance then this is the procedure to reset......."

Buzzer Reminder Cancel Mode Setting
1) Set the LCD on the combination meter to the ODO display.
2) Press and hold the TRIP meter reset knob for ten seconds or more within six seconds of turning the
ignition switch to the ON position. Fastening the drivers seat belt while holding the knob cancels the
buzzer reminder.
3) When this occurs, the LCD displays -OFF. The buzzer reminder can be switched between ON and
OFF each time the TRIP meter reset knob is pressed. The LCD displays -ON or -OFF according to the buzzer reminder ON/OFF status. The display changes to the ODO or TRIP meter if the knob
is not pressed for ten seconds.
4) Performing steps 1) and 2) again when the buzzer reminder is off exits cancel mode.
5) The cancel mode will also exit when the battery or combination meter connector is reconnected.

Press the info button until you see Trip A or Trip B. Once you are looking at the Trip meter you want to reset, press and HOLD the info button. After 3 seconds, the dashboard will beep and the Trip meter will reset to zero.