SOURCE: need wireing diagram to change 72 nova over to hei distributor
Hey , just take the positive wire from the coil you are removing and feed it to the + terminal on the HEI dist. cap.the other terminal under there is for your tachometer. If you are mounting a master kill switch in the bumper for drag racing- attatch the kill wire to the tach terminal also.
Thats it you just plug the three wire pigtail from the dist. base(pickup) to the cap and you are off.
Remember firing order is 18436572 in a clockwise direction. to find #1 remove #1 plug and have someone"bump" the engine over while holding your finger over the hole-carefull. then line up the slotted mark on the crank pulley with the big notch on the timing indicator. Good luck
SOURCE: distributor cap firing order 1993 chevy cheyenne truck v6
Firing order is 1-6-5-4-3-2 cyls. # 1-3-5 on drivers side front to back and cyls. # 2-4-6 passenger side front to back.
SOURCE: have an 88 Chevy c1500 305 Eng i want to change tbi to carburetor
2bbl intake will not fit 87-95 small blocks heads are diferent from pre 86.the center bolts on your manifold are angled different than the front and back bolts.your 2bbl manifold has the same angle bolts front to back.i converted my buddies 89 to carb,had to make adapter plate for carb.but to make a long story short there is a lot of power loss and fuel economy your better of with tbi.
SOURCE: Gm carb 305 timing problem
On the distributor, Check for advance weighrs. As your rpm increases the weights advance the timing. If they are rusted or a spring is streched or broken you will have to correct that. Hold the drive end and rotate thw rotor end back and forth to make dure the advance plate works freely and not sticking. It should spring back when you release it after turning it.What yr. is this rngine?Carburated, never mind. Ok, making sure the distributor is all free and cleaned up. Turn the dist. upside down and shake to make sure nothing falls out. You seem to have the timing thing down, but let me go through it just so I keep my train of thought.Actually I'm thinking out loud. #1 cyl on comp stroke-timing marks set to 8 degreesBTC. GO TO DISTRIBUTORdeternine #1 plug wire tower. Regardless of distributor body position as long as little tin window is around 6 o clock, Insert the distributor so the rotor is pointing at #1 tower.the mark you made so you know where that is..Should be @ 4 or5 o clock. When you drop the distributorin you will notice it turn so compensate soby dropping it a tooyh or two back.The rotor should be in the sweep of the #1 tower when you rotate the distributor. Hook up the coil wire and put the clamp on the distrutor but don't tighten it.With ignition on, #1 plug in #2 wire, lay the plug down on a good ground. Now slowly rotate the dristributor until #1 pops out a spark for you. You may have to go back and forth until you feel comfortable with when the coil fires. I don't know if you have a vacuum advance or not, but the vacuum advance points in the direction of distributor rotation. You want the spark to hit as you are rotating the distributor against the rotor rotation. Now the spark will hit at 8 degrees BTC before any weight or vacuum plays into it. Snug down your distributor and if you do have a little tin window, Stick the ole' in there and adjust the points to 28-32 degrees dwell. If no window, no sweat. It's an HEI, right? Let me know if you run into trouble. You can check your max advance if you like butgoing by that is assuming it's ok when it's not doing 3000 rpms. Better we assume the max is ok and know the bottom (start and low speed) is right on. Good Luck.
140 views
Usually answered in minutes!
×