How do I remove the original seat covers from a PT Cruiser driver seat

Moved category from Spanish car maker Seat (pronounced Cee-at), to Chrysler PT Cruiser.

Parts are available. Click on the Image tab for parts schematics.

https://www.google.com/search?q=2001+PT+cruiser+seat+parts

The seat belt switch cannot be adjusted or repaired and, if ineffective or damaged, the entire front seat belt and retractor (drivers side) must be replaced.
For more details on this issue,click the link below:-----
http://technoanswers.blogspot.in/2012/06/pt-cruiser-seat-belt-and-retractor.html

-------
This will help.
Thanks.

if this is a diesel its a days job,DISCONNECT BATTERY UN DER PASSENGER SEAT take front grill and the front cross member off drain radiator loosen all bolts on radiator do not undo any connections on air con. jack up car remove plastic belly plate remove drivers side wheel and inner plastic arch cover ther is also a strut that needs to be removed,using a screwdiver prise off the fan timing belt then remove 4 bolts underneath that hold the radiator up you will then need to remove drivers side headlight to gain accsess to the bottom alternator bracket, with this done you can then carefully remove the alternator and remove the bush box and replace the bushes

pop bottom cover off and check for debris caught around spool ,ratchet jammed or belt twisted these are the three most common problems

NEW LEATHER!

omg open the cover with a screw driver or twist the removal screw!!!

There may be some reasons of coming the airbag light on your PT Cruiser. Some connectors could be loose under seats or sensor of steering wheel could fail. However it is really rear. Your problem is probably caused by common problem in PT Cruisers - by broken wire on driver's seat.
Before you start doing anything disconnect a car battery. After 15 minutes remove a plastic panel from the seat (the one you can see when you open your door). Than you will see a wire in plastic cover. It connects an airbag in your seat and yellow connector under the seat. The wire breaks near to the second plastic T-shaped part (looking from the top of the seat backrest). It is located where is a pooling line and rising seat connector wire - somewhere in the center of lenght of the seat. Put the seat backrest to the vertical position, push up the black plastic cube of the line to remove it and have some room to repair the wire, cut a cloth tape. You should have ***** white and red wires. Inspect the wire about 1,5 inch from the center of the place where was the center of the T-shaped plastic keeper. The wire outside will be looking as new, but coper lines inside used to be broken. Strech slightly one by one of the 2 wires. When you find the break just cut the plastic cover in that place, remove 0,25 inch of the cover from each of cut end of wire and twist the ends or put extra 2 inch insert of the same wire. Wrap the coper wires in insulating tape neatly and tape all of the wires together with the T-shaped plastic keeper. Put on place the line udjusting a backrest of the seat, the keeper and plastic cover of the seat. Connect a battery and check it.
If you are not sure where is the place whre the wire could be broken, it is exactly 30 centimetres from the connector of the airbag. TomasS

The first code is for "driver seat track position sensor low". The module detects that the sensor input is less than or equal to 0.3 mA. The second code is referring to the first code. I have no idea what the third code is. Basically you have two different communication systems mixed. The 2001 uses the PCI bus system and the 2007 uses the CAN bus which is much faster. The first code is a CAN bus code and the second is a PCI code. As far as the airbag deploying in the event of a collision, I don't believe it will with an active code in the system. I hope this helps.

is it round or rectangular?

Neoprene two tone seat covers are available at State of Nine but are pricey. You can spend about $250 and perform a DIY leather repair and dye job to the entire interior. Here is what I did, using leather cream crack filler and auto leather dye. It lasts about three years and then requires touching up.