My egr valve was cleaned n put back on then 1 hour later my car ciesed up.is this because of the egr valve.on my 1997 buick leasaber

CHECK UTUBE

This code indicates a problem with the EGR valve's pintle position. The EGR Valve's pintle could just be stuck in which case the problem could be fixed by cleaning the EGR valve.

If the EGR valve is electronically controlled or cleaning the valve does not fix the problem, you will most likely have to replace the EGR Valve.

Keep in mind that the EGR valve relies on inputs from other sensors to determine the pintle position. If one of these other sensors is not operating correctly, it could be giving you a false P1406 error code.

Many times, this will go off and it won't be a problem. Just go ahead and take it off to make sure it is not clogged. Just go ahead and clean it out. You might need th change the egr sensor. It may be given off a false reading. As long as it looks good,it is clean, and nothing is in its path, it should be good. Is your Rodeo acting up any?

Below is a link for instructions for the removal and installation of the EGR valve along with a diagram. Best of luck.
Greg
97 Buick EGR

Check the passages under the airhorn. When carbon builds up the diagnostic blames the EGR for not opening and throws a code. Actually there is no flow to the EGR because the port is clogged and the diagnostic measures the flow after the EGR.

They really needed to have a sensor before and after the EGR. Also remember to disconnect the battery for 10 minutes to remove old info.

Check for

vacuum leaks on intake manifold,

the air tube between the air filter.

intake manifold vacuum hose.

===
clean throttle plate with Berryman carburator cleaner

SEE sample picture HERE
===

Also remove carbon built up behind the EGR valve and the EGR passage tube.

===

Vacuum leak WILL offset the intended 14.7 to 1 air fuel ratio.

More un-metered air (leaks) will lean out the fuel mixture.

Use small amount of Berryman carb clearer at potential air leak area will help you identify trouble spot.

At idle,just spray and listen for the RPM surge.

The in-rush of carb clearer will increase the RPM on the motor.

Record the problem spot(s) and address it later.

===

EGR carbon built up require 2+ hours to clean from start to finish.

You will need a new EGR base gasket before your start.

Locate and remove the EGR valve after the vehicle is cool down.

Carefully record the connector and vacuum line (for older vehicle) location by drawing an easily to follow diagram.

Remove the EGR valve.

Inspect the location of the carbon built-up inside the valve and the EGR passage tube.

SOAK these areas with WD-40 spary.

You will need a small screwdriver,cloth hanger and lot of newspaper and time to get this cleaning done right.

RE-SOAK the carbon and let it sit for over-night will also help.

One the last round,pass a shop vacuum of the EGR valve and the passage pipe.

Install the new EGR gasket and connectors.

Allow the vehicle to warm up outdoor to burn up any remaining WD-40.


Take it for a test drive.


Please rate my answer if it's useful to you.


Cheers,

Mustgo

egr flow problem egr solenoid did not work properly.

remove the egr valve take a piece of clothes rack or a tiny tiny screw driver carefully clean out carbon in the intake port hole on the intake.the carbon blocking off the egr valve.so it cant work properly.after cleaning carbon clean up the debris and go from there.

Yes it Still Can be the EGR valve Replace it i found one For About 69.00 OEM they normally run for 89-120. Replace it just cleaning it is not enough they go bad especially if its original. and they tend to read same codes when its bad.Hope this Helps.

P1400 on your vehicle is described as :Differential Pressure Feedback EGR Circuit Low Input You either need a new DPFE valve, or a new EGR valve. Both can be tested for functionality before replacing them both. EGR valve is more likely I think. Cleaning it may not improve its performance, but its worth a try. Also check the vacuum lines between the DPFE and EGR system. The EGR valve and DPFE are usually close together above the exhaust manifold/downpipe. you need service instructions to test these items, suggest you go to a garage really...