Why do I hear my 2000 Malibu beep 14 times on the drivers side of vehicle and then stops?

You may need to change the wiring harness.

2000 malibu headlight problem - Tech Support Forum

www.techsupportforum.com > ... > Automotive Support

Dec 14, 2008 - 8 posts - ‎2 authors
I have a 2000 chevy malibu with headlight problems. ... High beams work correctly.... I suspect a ground problem but cannot locate the ground cluster. ... Grouped together there, one pink wire to the Headlamp Switch, and one to ... my Wife's car has lowbeam on the left side that just won't work and now the ...

Chevrolet Malibu Owners: Problems & Solutions - Edmunds.com ...

www.topix.com > Ohio > Franklin County > Blacklick

Apr 9, 2010 - Goes Beep beep and then stops for several minutes and does it again. ...The alarm/ignition module needed to be changed @ dealer ($500.00 ++++) ... weak, replaced and voltage ranged from 12.12 to a max of 13.8 at 2000rpm. ... i have a 1981chevy malibu and when i try to start it wont turn over and the ...

1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch to UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones). 11. Remove the ignition key in order to exit the Program Mode.

There is none. Sorry. It's GM design for that. You need to raise the vehicle on level ground and open the drain (located on the driver side and is accessible from underneath the vehicle)

Time for a new seat, I'd buy a used seat online for cheaper.

The beeps happen when speeding up and passing other car

does the airbag light come on when you start vehicle? If the lamp is out it will give an audible beep.

under hood fuse box on drivers side of vehicle, there should be a number diagram on inside of cover.ight headlight is #50 and left headlight is # 51, they are mini fuses. fuel guage works off of sending unit in tank! if it does not work check sending unit or a bad gauge.

1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.

I dont know why it would make that sound. I dont know the MPH to KMPH difference, but the car should not be able to go over 110MPH . The noise you are hearing is probably coming from a little solenoid below the glove box. I actually took mine off and put in a silicone, wich quietned it a whole lot. This was a long time ago, but I dont think there was a way to disconnect it, it had other uses.