How do you take off the power driver's side mirror of a 2001 ford zx2?

For all types of power window problem and power windows not working,i suggest you to go through the help links given below. Click the link to go through its procedure to troubleshoot the problem :------

Power window problem
http://repairhelpcenter.blogspot.com/2012/01/pontiac-grand-am-power-window-not.html
------------

Power windows not working after car wash?http://howtobyme.blogspot.com/2011/11/power-windows-not-working-after-car.html
---------

power locks, power window and power mirror not working?
http://howtobyme.blogspot.com/2011/09/power-locks-power-window-and-power.html
------------
All power windows not working?
http://howtobyme.blogspot.com/2011/09/all-power-windows-not-working-on-2003.html
------------
How to remove window motor and regulator on Car?
http://howtobyme.blogspot.com/2011/09/how-to-remove-window-motor-and.html
-------------

Complete Diagnosis & Testing Power Windows?
http://repairhelpcenter.blogspot.in/2012/02/diagnosis-testing-power-windows.html
-----------This will help.Thanks

If it has a manual transmission, check the clutch start switch on the clutch pedal support. If it has an automatic transmission it could be the transmission range sensor mounted on top of the transmission right side of the engine. In either case it could be the ignition switch (this is the switch you put the key in to start the car).

Take out the mirror switches and spray it with electronic cleaner or electrical cleaner. This is a common problem with power mirrors.

Click on the following direct Link. They have several diagrams for your Escort ZX2 Belts which will match your specific engine size and options ( AC/No AC etc). It also has several other diagrams for your future use.

Let me know if this helped....

For the 2001 Ford Escort ZX2:
http://www.2carpros.com/car_repair_information/year/2001/make/ford/model/zx2/2001_ford_zx2_drive_belt_routing_diagram.htm

The idle air control vavle is located on the driver side of the intake manifold, below the throttle body. You'll have to remove the air intake to see it. It is held there by two bolts.

Under hood driver side, upper engine area, mounted on valve cover, disconnect hose at PCV, pull PCV valve out insert new one and reconnect hose.

are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

1. Remove the front door trim panel; refer to Section 501-05 .
2. go to car-part.com for a used mirror. Page with * is cheapest seller.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

------------------------------------------------------

----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors

1. Position the glass in the full up position.

1. Locate the notch at the bottom of the exterior mirror glass.

1. Release the exterior mirror glass.
   1. Insert a long flat-bladed screwdriver in the notch.
   1. Push the screwdriver into the notch until the glass is released.

Heated mirrors

1. Position aside the exterior mirror glass.

1. Disconnect the electrical connectors.

All mirrors

1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.

Installation
Heated mirrors

1. Connect the electrical connectors.

All mirrors

1. Position the exterior mirror glass on the exterior mirror motor.

1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Its "doable" but I wouldn't advise you to do it that way. Get a phillips screwdriver to unscrew the elbow pad & any other screws holding the door panel on. Disconnect the pwr window switches & any other switches on the panel. On the lower end of the door panel there are plastic clips holding the panel to the door. POP them out of the door & remove the panel. disconnect the mirror electrical connector & disconnect the mirror body itself. Install the new one & don't forget to connect all of the electrical connectors & reinstall the panel. Good luck

the thermostat is on the front right side just below the air tube (which you have to remove) in a black hard plastic case. It is a PAIN IN THE ARSE to get to, it will have 2 sensors sticking out of it, on on the bottom, one on the side.

you have to take the door panels off. remove all screws you will have plastic pieces called christmas trees that hold the panel in place. there is a tool for this you can pick it up at Napa for cheap this will allow you access to the inner space of the door un plug plugs to power switchs and the rod to your door catch hardeware you then can remove panel completely to get access to mirror assembly. installation of door panel is in reverse