I need detailed printable instructions for removal of an alternator on a 2002 dodge intrepid
SOURCE: 2002 dodge stratus 2.4L dohc water pump and timing instructions
This procedure is wayyyy to long to list on here. Your better off going to your local auto parts store and buying a repair manual for your car. It will have both detailed procedures for fixing both of your items. You can also goto the library and get the factory service manual for free. Good luck to you and thanks for using fixya!
Sincerely,
jC
SOURCE: 99 dodge intrepid blower motor not working
No. Pull out right front inner fender well cover and motor is on firewall. Four bolts max.
SOURCE: I need a time diagram of an 2002 dodge intrepid,
Hi there;
Here is a picture of the timing marks for the 2002 2.7L intrepid engine.
Hope this helps
Farrout!
SOURCE: Replacing the broken cup holder
First, you must remove the floor console bezel (the trim piece that surrounds the shifter knob). The proper method to remove this involves removing the shifter knob first. This is held in by a small set screw on the "radio" side of the knob. To remove the screw, you will need a small "hex-key" (also known as Allen key or Allen wrench). The proper size is 3mm, but you can get away with using a size 7/64" if you need to. Once loosened, I believe that the knob pulls right up and off. Make sure you do not lose the small screw. Also be careful not to accidentally contact the tip-top of the shifter while the knob is removed, as this may break off the small black plastic tip, which will require much more work to repair and/or replace the entire shifter.
Next, you should be able to remove the floor console bezel by prying gently and carefully on the corners and sides of the piece with a tool called a trim stick, or if you do not have this tool, you can get away with using a small, thin-tipped flat head screwdriver. However, this will almost surely cause some aesthetic damage to the edges of the trim.
Once this bezel is out of the way, (you shouldn't have to remove the electrical connectors on the underside of the bezel for this specific job) there are 2 screws holding down the bottom of the cupholder assembly. I believe these are both Torx - type screws, which will need either a T10, T15, or T20 screwdriver bit to remove(I'm sorry but I don't remember exactly which of the 3 sizes are used). After these 2 screws are removed, open the armrest. On the TOP of the FRONT of the armrest, just above the cupholders, are 2 more screws which should be the same as the 2 bottom screws. Remove these, then lift the cupholder assembly up and forward to remove it.
To install, simply reverse the above procedure.
Because this is my first solution posted on this site, I would love to have your feedback. Please let me know how everything goes with this project. Thank you!
Mitchell
SOURCE: Serpentine/drive belt routing diagram of a 2002 dodge Intrepid needed.
Try this web sight. http://www.dodgeintrepidchat.net/02lhe/
Unhook the battery. Remove the negative cable first, then the positive one.
Lift the front end of the car, using the jack, and place it on jack stands. Refer to your owner's manual for a placement diagram--they are in an unusual location for the 2001 Dodge Intrepid.
Remove the plastic splash guard from the underside of the engine. It is held in place by several bolts.
Unbolt the transmission cooler, then move it out of the way. Don't remove the hoses--just the bolts.
Remove the brace that holds up the radiator. Use a jack stand to hold up the radiator.
Loosen the adjustment T-bolt and pivot bolt on the alternator, but don't remove them. Remove the belt.
Unscrew the nut that holds the battery cable to the alternator, then remove the cable. Unplug the other electrical connector, as well.
Unbolt and remove the alternator.
Replace the alternator. The steps are the reverse of the removal procedure. Torque the nut on the battery cable to 90 in-lb. Torque the mounting and pivot bolts to 40 ft. lb.
97 views
Usually answered in minutes!
×