1996 Chevrolet Blazer Logo

Related Topics:

A
Anonymous Posted on Sep 30, 2014

Will the K1500 rear backing plates work on a 1996 Chevy Blazer

I have been searching for these plates for my vehicle and no seems to have that type of part for my blazer

5 Related Answers

s60six

  • 328 Answers
  • Posted on Dec 21, 2008

SOURCE: Where is the dipstick on my 1996 Chevy Blazer?

if its the transmission dipstick you are looking for. Its on the passenger side of the engine at the rear of the engine compartment.........on a 96 it should be red and flip up and then pull it out to remove it.........as for filling you need a funnel with a very small hole at the end and the fluid goes in the hole the dipstick comes out of...........sorry no diagram though.....:(
hope this helps!

Ad

Anonymous

  • 82 Answers
  • Posted on Mar 11, 2009

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Anonymous

  • 1111 Answers
  • Posted on Sep 08, 2009

SOURCE: 1996 chevy blazer my air on heater will not blow

the idea of the switch is run on vacuum and is not making contact with the switch it self either worn contacts in the switch itself **** as an obstruction as well or the vent door is stuck in just that position either behind the glove box or the ash tray are the vacuum lines one of them may be pinched off or the door needs a bit of help until you can free it up

Anonymous

  • 6982 Answers
  • Posted on Sep 10, 2009

SOURCE: Replace 1996 Chevy S10 Blazer sway bar bushings

You can do that in the ground but it is easier to have a jack handy to get the bolts to align back in the chassis by changing vehicle loading on bar. No special stuff I know of...

Anonymous

  • 6 Answers
  • Posted on Sep 03, 2010

SOURCE: 1996 chevy blazer tire size

stock is generally the 235/75r15, but if you can find someone to install them or do it yourself easily be able to run 31x10r15 for a little meatier look, this would involve a slight trim of the front skirt edge on some models or depending on your suspension. Any tire shop would easily be able to tell you stock tires or what would fit, but most major retailers (walmart, fleetfarm) will not install ANY tire not listed as factory. so you would have to find a private shop then.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

1999 Chevy Tahoe. Will this transmission from a Tahoe work?

The links lead me to believe there are interchangeable. In fact this page confirms the compatible models

https://shiftritetransmissions.com/shop/4l60e_98-05_4x4/

1998-1999 Chevrolet Silverado K1500 4.3L 4X4
1998-1999 Chevrolet Silverado K1500 5.0L 4X4
1998-1999 Chevrolet Silverado K1500 5.7L 4X4
1998-1999 GMC Sierra K1500 4.3L 4X4
1998-1999 GMC Sierra K1500 5.0L 4X4
1998-1999 GMC Sierra K1500 5.7L 4X4
1998-2000 Chevrolet Tahoe 1500 5.7L 4X4
1998-2000 GMC Yukon K1500 5.7L 4X4
1998-1999 Chevrolet Suburban K1500 5.7L 4X4
1998-1999 GMC Suburban K1500 5.7L 4X4
1999-2000 Cadillac Escalade 5.7L 4X4
1999-2000 GMC Yukon Denali 5.7L 4X4
1998-2005 GMC Safari 4.3L 4X4
1996-2005 Chevrolet Astro 4.3L 4X4
1996-2005 Chevrolet Blazer 4.3L 4X4
1996-2001 GMC Jimmy 4.3L 4X4
1996-2001 Oldsmobile Bravada 4.3L 4X4
1998-2001 GMC Envoy 4.3L 4X4
1996-2004 Chevrolet S10 4.3L 4X4
1996-2005 GMC Sonoma 4.3L 4X4

https://www.google.com/search?q=1999+K1500+push+button+transmission+4WD

https://www.google.com/search?q=1999+Chevy+Tahoe+push+button+4WD+transmission+4L60E



1999 - 2006

0helpful
1answer

I need to know witch wire are wxtch on the bulkhead conectoron the driver side of my 1996 chevy k1500

Type into your google bar "wiring harness at cowel connection for 1996 Chevrolet K1500 pickup". This will get you the wiring configuration you search for. Google can be your friend if you use it.
0helpful
1answer

Will a 1996 chevy blazer LS 4wd differential fit into a 2000 chevy blazer LS rwd rear end ?

Measure the lenth of both rear ends. see iss all hardware will bolt up without fabrication. if its the same size it will work. But im afraid being a 4 wheel drive it will be geared lower then a regular pick up/ Drive shaft may work but if not it would have to be shortened or lenghthebed. alot of work. Brakes you could leave the non drum breaks on better stopping power. I honestly believe you would be better off just going to a scrap yard and find one very easy to remove and replave few hour job.
0helpful
4answers

Which other vehicles use the same rear end as 1996 Chevy Blazer 4 by 4 with 7.5 in ring gear

The chevy s-10 pick up, GMC Jimmy, chevy Astor van would have a rear end that would line up and fit.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/tom_db3a51ff0ca57f20

1helpful
3answers

I lost my keys to my Chevy blazer 1996 yesterday ...a mechanic came by and removed the Lear latch lock to make a new key ...but at the end he was unsure if I could start the ignition with it ....is the...

No your ignition is a different lock but it could be keyed the same by a locksmith or possibly one could be ordered to match it from the factory based on your vehicle identification number.
0helpful
2answers

Why is the back plate for my 1995 Chevy K1500 stepside cost $350.00? years before and after are around $30 bucks. What's up with this?

Because GM likes to change things for no reason at all. The 305 and 350 engines in the 80's and 90's have three different rear main seals. No reason at all, same transmissions and engines, even same engine codes, but different seals. They do this all the time and this is why, among other reasons, I don't buy or own GM or Chrysler vehicles.
5helpful
1answer

1996 Chevy K1500 4L60 Transmission having problems shifting speedometer is at Zero no movement and ABS light comes on.

The vehicle speed sensor is not working, it is located in the transmission tailshaft. The computer uses this speed info to shift the transmission, and tell when the rear wheels are locked up so the ABS will function.
1helpful
1answer

Trying to remove spare tire from under a 1996 Chevy Blazer

lug nut wrench goes in a hole next to your rear license plate... turn until the tire lowers all the way
0helpful
1answer

Parking light dont work in back and no blinkers in back

CHECK FUSES AND GLOBES OR THERE MAY BE A PLUG FROM FONT TO REAR ALONNG THE KICK PANNEL THAT HAS CORODED
Not finding what you are looking for?

48 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...