<!-- from fixya rte -->Honda engine d12y8 crank torque sequence - 1996 Honda Civic

https://www.google.com/search?source=univ&tbm=isch&q=ft.+pounds+for+1993+honda+accord+2.2+crank+cap+bearing&hl=en&sa=X&ved=2ahUKEwjK5tT8xLHpAhWHTcAKHeGvD_YQsAR6BAgFEAE&biw=1326&bih=627

Main Bearing Torque Sequence

1. Hand tighten bolts 1D, 1G and 1F until the bedplate contacts the block.
2. Tighten bolts 1A-1J to 40 ft. lbs. (54 Nm).
3. Tighten bolts 1- 8 to 62 inch lbs. (7 Nm).
4. Turn bolts 1-8 an additional 90°.
5. Tighten bolts A - E 20 ft. lbs. (27 Nm). Fig. Main bearing torque sequence-3.7L engine.

https://www.autozone.com/repairguides/Commander-2006-2007/Specifications/Torque-Specifications/_/P-0996b43f8075a69a

https://ibb.co/qd98Tw4

Click on the link for sequence, engine oil pan. torque in two or three steps, in sequence, final step torque 8.7 ft lbs. Usually if ft lbs are low, I use an inch lb torque wrench, multiply by 12. Just my opinion.

this is very authentic engine its very helpful information for us. I was read this blog about this engine https://www.360ghostwriting.com/book-promotions information

1998 Isuzu Truck Rodeo 2WD 2.2L MFI DOHC 4cyl

The Head Bolt Torque

Torque sequence ----------------- front ' 7 3 1 5 9 ' of ' ' engine ' 8 4 2 6 10 ' ----------------- Step 1: torque bolts in sequence to 18 Ft/Lbs Step 2: turn bolts in sequence an additional 90-degrees Step 3: turn bolts in sequence an additional 90-degrees Step 4: turn bolts in sequence an additional 90-degrees recheck final torque in sequence

1998 Isuzu Truck Rodeo 2WD 3.2L MFI DOHC 6cyl

The Head Bolt Torque

Torque sequence -------------- front ' 6 1 3 7 ' of ' ' engine ' 5 2 4 8 ' -------------- Step 1: torque to 20 Ft/Lbs Step 2: torque to 47 Ft/Lbs recheck final torque in sequence

Removal sequence: ---------------- ' 2 8 10 6 4 ' front ' ' of ' 3 5 9 7 1 ' engine ----------------******************************************************Torque sequence: ---------------- ' 9 3 1 5 7 ' front ' ' of ' 8 6 2 4 10 ' engine ----------------****************************************************** Step 1: torque bolts in sequence to 14 Ft/Lbs Step 2: torque bolts in sequence to 36 Ft/Lbs Step 3: torque bolts in sequence to 49 Ft/Lbs Step 4: retorque bolts (1) and (2) to 49 Ft/Lbs

Tighten the cylinder head bolts to their final torque specification in two steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts.

1. Step 1: Tighten each bolt to 22 ft. lbs. (30 Nm).
   
2. Step 2: Tighten each bolt to 61 ft. lbs. (85 Nm).

Fig. Cylinder head bolt loosening sequence - 1.6L (B16A2) engines (click image for zoom)

Hope helps.

Hello claudian1535,

Below is an image showing the torque sequence. The torque procedure is a three step process:

Step one torque all head bolts to 14 ft.lbs.
Step two torque all head bolt to 36 ft.lbs.
Step three torque all head bolts 49 ft.lbs.




I hope this helps.

Regards,

netvan

CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

1978 - 1980 FORD FESTIVA 1.6L 65-70 Foot pounds (Final torque)
Torque sequence 9 3 1 5 7 8 6 2 4 10 Step 1: torque to 5 Ft/Lbs Step 2: torque to 20-30 Ft/Lbs Step 3: torque to 50-55 Ft/Lbs Step 4: torque to 65-70 Ft/Lbs Recheck final torque in sequence


1988 - 1993 F0RD FESTIVA 1.3L Torque sequence front of engine 8 4 1 5 9 7 3 2 6 10 Step 1: torque to 35-40 Ft/Lbs Step 2: torque to 56-60 Ft/Lbs Recheck final torque in sequence

2011 FORD FESTIVA 1.6L NO TORQUE SPECS AVAILABLE THERE IS NO FORD FESTIVA MANUFACTURED IN 1998 ALSO NO FORD FESTIVA MANUFACTURED WITH A 1.5L ENGINE
HOPE THIS HELPS YOU

Torque.

Step 1- 22 FT.LBS.

Step 2- 48 FT.LBS.

Hope this helps you.