P1401 Differential Press Feedback EGR Circuit High Input
Your EGR port is plugged. Replace your EGR valve, and clean the ports
A code P0302 may mean that one or more of the following has happened:
SOURCE: 98 E-250 Rough Idle; codes p0156,p1131,p1151,p0301,p0171,p0174+
po301 thru po306 all misfire codes cylinder 1-6 remove plugs and replace them..... set the plug gap first
i suggest u replace the wires also if they never been replaced all these misfire codes can set the others and one is for the oxygen sensor ( 02s or HO2S) CIRCUT MALFUNCTION do u know how to check wireing systems
do the tune up plugs (set gap) .052-.056 change the fuel filter also. clear the codes hows it run
this info is for 98 E-250 4.2Litre
what engine do u have 4.2L or 4.6L i know it is a v-6 by the codes
SOURCE: start and diesss
p0456: evap system. sensor failure
p0172: evap system. intake blocked
p0778: exaust valve control. solenoid/ecu faukt
p0300: cylinders misfire. check ht/ignition leads
p0301,303,304,305,306: same ht leads
hope this helps..
SOURCE: 07 lexus rx 350 with check engine light code p0304
Hi, did you ever get an answer? I have the same issue. Thanks.
SOURCE: my 2001 jeep grand cherokee laredo is having
P0300 Diagnostic Code - Random/Multiple Cylinder Misfire Detected
Basically this means that the the car's computer has detected that not all of the engine's cylinders are firing properly.
A P0300 diagnostic code indicates a random or multiple misfire. If the last digit is a number other than zero, it corresponds to the cylinder number that is misfiring. A P0302 code, for example, would tell you cylinder number two is misfiring. Unfortunately, a P0300 doesn't tell you specifically which cylinder(s) is/are mis-firing, nor why.
Symptoms may include:
the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present
Causes: A code P0300 may mean that one or more of the following has happened:
Faulty spark plugs or wires
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector(s)
Burned exhaust valve
Faulty catalytic converter(s)
Stuck/blocked EGR valve / passages
Faulty camshaft position sensor
Defective computer
Possible Solutions:
* If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
* If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.
Random misfires that jump around from one cylinder to another (read: P030x codes) also will set a P0300 code. The underlying cause is often a lean fuel condition, which may be due to a vacuum leak in the intake manifold or unmetered air getting past the airflow sensor, or an EGR valve that is stuck open.
About P0301 or P0302 code, this means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #1 and #2.
Symptoms may include:
the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present
Causes: A code P030x may mean that one or more of the following has happened:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer
Possible Solutions:
* If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
* If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.
Hope helps (remember to rate and commet this answer).
SOURCE: my car is cutting off
Hi P0305 is misfire in cylinder #5. Please get back to us if you have further query or else please
accept the solution. Thanks for contacting fixya.com
P0306 is misfire in cylinder#6.
P0316 is misfire on start up.
Have the plugs on those 2 cylinders, and the 2 fuel injectors checked, also
check for spark from the coil on those 2 plug wires.
Hi
P0305 is misfire in cylinder #5.
P0306 is misfire in cylinder#6.
P0316 is misfire on start up.
Have the plugs on those 2 cylinders, and the 2 fuel injectors checked, also
check for spark from the coil on those 2 plug wires.
Please get back to us if you have further query or else please
accept the solution.
Thanks for contacting fixya.com
434 views
Usually answered in minutes!
×