2013 Harley trike no reverse

Question edited for clarity.
Question moved to model category.

It isn't a module, just a switch. There appear to be 'issues'.

https://www.google.com/search?q=2013+Kia+Ceed.+Reverse+light+module+location

..

Don's 1999 Ford Ranger shift motor PROBLEM SOLVED ...

? 13:05
https://www.youtube.com/watch?v=wcn39gwPWfI
Oct 1, 2013 - Uploaded by gtarman49
Don's 1999 Ford Ranger shift motor PROBLEM SOLVED. ...How to find replace fix 4x4 transfer case shift module 2002 Ford Explorer 4 wheel ...

How To Install Replace 4x4 Transfer Case Shift Motor Ford ...

? 9:15
https://www.youtube.com/watch?v=9ldrtZODxQ8
Oct 26, 2010 - Uploaded by 1A Auto Parts
How To Install Replace 4x4 Transfer Case Shift Motor Ford Explorer .... transfer case shift module 2002 Ford Explorer 4 wheel drive not working ...

How to find replace fix 4x4 transfer case shift module 2002 ...

? 3:07
https://www.youtube.com/watch?v=sZw3SS2Pt-4
Nov 3, 2013 - Uploaded by kirk colombo
... transfer case shift module 2002 Ford Explorer 4 wheel drivenot working ..... I replaced the transfer motor so i think it is the control module.

Hey I'm having the same problem with my BMW 320d 2005 car. Fuses, switches ,bulbs are all fine abd reversing lights still not working . Please help me out

This is a failure of the "remote function actuation module". It is located under the rear deck next to the right rear speaker. The rear seat must be removed to access it along with removing the rear deck. It controls the trunk release, door locks, dome light, and reverse light. My remote trunk release stopped working along with the relase button on the dash along with the reverse lights failing at the same time. The module is over $150 so I would try to find a way to rewire the lights to work without the module.

The DTR switch on the side of the transmission, that the shifter hooks to, to change the gear positions may have gone bad. Usually about fifty dollars,but you have to get it adjusted right,and that means using a shop manual to install it. don-ohio

Hi, the reverse lights run threw the neutral safty switch.It may be out of adjustment,have a bad gromet on the shift cable or the switch is bad.It is located on the transmission under the shifter cable.Testing the switch. Turn the ignition to the on poss.with the gear selector start in the park poss. move threw rev.to neutral and watch for the lights to come on if thay come on adj.the switch or replace the gromet.If lights don,t come on,replace the neutral safty switch. Hope this helps. Thank You for using fixya.......iluv2fish..Ray...

On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

you have a bad lighting control module. $499 new, $250 from tascafordparts.com or less from ebay or car-part.com.

It is under dash above brake pedal.

Section 17-01: Lighting, Exterior 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Lighting Control Module Removal and Installation

1. Open hood. Disconnect battery ground cable .

1. Disengage three pushpins and remove lower driver side instrument panel finish panel.

1. Locate lighting control module above accelerator pedal.

1. Disconnect bottom two electrical connectors from lighting control module.

1. Remove two screws retaining LCM to bracket and unclip from bracket.

1. Remove lighting control module from bracket and disconnect two remaining electrical connectors.

1. To install, reverse Removal procedure. Check lighting control module for proper operation.

I can relate ... been without reverse lights for a while.
Here's my understanding of the communications that take place in this process: when you put the vehicle in reverse, there is a backup light switch on the transmission that sends a signal to the Transmission Control Module (TCM), that then forwards that information to the BCM, and the BCM sends the signal to the backup lights.

Have had different diagnoses for the problem ranging from BCM (body control module), to FCM (front control module), to the standard bulb, wiring, etc. Dealer wanted to do a $1000+ job thinking it could be the BCM. Being cheap decided to do some troubleshooting on my own ... with help from another site where I contacted a Dodge Expert.

In my case, we tested wiring, and found there was a fault in the wire ... replaced with a new wire.
So sending 12V to from the battery to the lights made the reverse lights come on -- so wiring and bulbs good.

Didn't fully fix the issue ... tested the pin from the BCM that carrys the signal to the backup lights to come on and found that the BCM is NOT sending out the signal. Looks like it is a BCM issue but want to check to make sure the BCM is getting the right input signal. So that is now where my testing will go.

Hope that helps.