We had the car serviced numerous times and spent a lot of money at different olds dealers and they could not find out the cause
SOURCE: service engine soon light come
i have never seen it on the console do that ,i know my engine light has stayed on for about four years and it is the turbin speed sensor in transmission but it dosent give me problems but then it started to flash and it was running bad ended up being injectors
SOURCE: I have a 1996 volvo 960 and the check engine light
Your vehicle’s computer system has self-testing capability. When the computer senses that there is a problem with one of the components or sensors it stores the correspondent trouble code(s) in its memory and lights up the "Check Engine" or "Service Engine Soon" light to tell you that there is a problem and you need to diagnosed and repaired it. The list of possible codes number in the hundreds. The code itself doesn't tell exactly what component is defective - it only indicates where to look, or what engine parameter is out of normal range. You or a technician will have to perform further testing to pinpoint cause and the proper repair. The light flashing when you are driving indicates a more serious problem that should be fix right away or more problems can occur.
Dave.
SOURCE: Service Engine light flashes for short time on highway Runs Rough
You need to have the system tested for trouble codes, Kragen and Autozone parts stores do this for free.
SOURCE: Transmission issue? Or worse?
Hello! Although the symptoms you've described could be a result of quite a few things, I have a few questions that might help determine your problem.
1) What year/make/model did the new transmission come from?
2) Is the SES (Service Engine Soon) light on? Is it blinking?
3) Was this transmission a rebuilt or used unit?
Some possibilites:
- you could have a faulty TPS - or Throttle Position Sensor.
- you could have a problem with the input shaft piston being worn. (Hence the used vs. refurb trans question). Once the inner sealing area wears it can prevent the inner lip seal for the piston from sealing properly. You may find that revving the engine up will finally get the car to move and it will BANG into gear. This is because the pump in the transmission is working harder and moving more fluid thus allowing the added fluid to overcome the leak which prevented the clutch from either initially applying or staying applied. Another area of concern that causes this is a boost valve in the valve body, not near as common but it can cause this problem on a lessor scale.
- Trouble Code P0742 TCC Stuck ON:
When this trouble code is set the pcm will command max TCC and lock adaptive shifting. This code can be broken down into three potential problem areas as found to be common in the field.
1. This problem can be a mechanical problem. Possible causes of this could be a bad or stuck TCC switch that signals the pcm of current TCC operation. Another cause though not common is a stuck TCC switch or apply valve. If it is physically stuck in the wrong position it can cause the TCC to be stuck on all the time and even kill the engine when the vehicle is put into gear.
2. This problem can be found to be an electrical problem. If the wire from the TCC pressure switch to the pcm is grounded anywhere in the path it can throw this code. This could be a wire shorted inside the trans on the internal wiring harness or the actual engine wiring harness. If the wire is grounded the pcm thinks that TCC is on when it shouldnt be and will throw the code.
3. This problem can be a hydraulic problem. This is the most common cause of this code that I have found and stems back to a clogged TCC solenoid, not because it failed. Excessive debris in the transmission or a failing torque converter lockup clutch can cause the solenoid to have debris stuck inside and this causes a restriction in fluid flow through the solenoid. If the solenoid can not bleed off the pressure the TCC can be stuck on. If the wrong TCC solenoid is installed during an overhaul this problem can also arise as a late 4L60E solenoid is identical but does not operate the same and acts like a clogged solenoid. As mentioned in problem #1 a stuck TCC apply valve is a physical problem but causes a hydraulic problem because the fluid pressure will not properly bleed off because the valve is stuck in the wrong position instead of being able to move freely in the bore of the valve body.
Above are the common causes of this code, there are other possibilities but those are what generally causes the fault. A thorough diagnosis is the only way to determine what is really at fault and a new TCC solenoid should never be assumed as the actual problem until verified.
HTH - and thanks for using FixYa!
-KCGTODAD
Testimonial: "Excellent feedback, thanks!"
SOURCE: 2003 Audi A6 ESP and ABS Lights Activate
I am having the exact same problem. The new sensor under the rear seat did not solve the issue. Does anyone have a solution?
47 views
Usually answered in minutes!
×