How to install rear wheel bearing on 2008 ford edge

SOURCE: what torque for rear wheel bearing Ford Focus 2000

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

SOURCE: 1996 ford windstar - changing rear wheel bearing passenger side

No on this model they are held in by a nut and cotter pin. You can remove them by hand.

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .

1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .

1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.

1. Remove the differential pinion shaft (4211).
   1. Remove the differential pinion shaft lock bolt (4241).
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Remove the U-washer (4N237).
   1. Push the axle shafts (4234) inboard.
   1. Remove the U-washer.

1. CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
   Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. CAUTION: Do not damage the wheel bearing oil seal.
   Remove the axle shaft.

1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.

1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
   Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.

1. Lubricate the new rear wheel bearing with the specified lubricant.

1. Using the special tools, install the new rear wheel bearing.

1. Lubricate the lip of the new wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Using the special tools, install the new wheel bearing oil seal.

1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

1. Lubricate the lip of the wheel bearing oil seal
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. CAUTION: Do not damage the wheel bearing oil seal.
   Install the two axle shafts.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Install the U-washer.
   1. Position the two U-washers on the button end of the axle shaft.
   1. Pull the axle shaft outward.

1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
   Install the differential pinion shaft.
   1. Align the hole in the differential pinion shaft with the case lock bolt hole.
   1. Install a new differential pinion shaft lock bolt.

1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.

1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. Install the rear brakes. For additional information, refer to Section 206-04 .

1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .

1. Lower the vehicle.

Jason Phillips

• 500 Answers
• Posted on May 20, 2009

SOURCE: Rear Wheel bearing needs to be replaced

the bearing has to be pressed in, quite the job even doing it at the shop- you will have to have some sort of press to press the bearing in.

SOURCE: replace rear wheel bearing 2002 ford explorer 4x4

you must remove brakes, then remove axle nut, then remove upper control arm and finally tie rod stabilizer, remove axle from car then bearing can be accessed. this is a difficult job that requires special tools so be careful