How do I change oil pan gasket on 2007 Chevrolet equinox?

Yes, all oil pans need gaskets. The torque is 18 ft lbs. PDF file

Oil Pan Replacement - ChevroletForum

https://chevroletforum.com > forum > equinox-23
PDF
2005 Chevrolet EQUINOX. Submodel: LT ' Engine Type: V6 ' Liters: 3.4. Fuel Delivery: FI ' Fuel: GAS. Oil Pan Replacement. Tools Required. J 39505 Torque ...


Do you need to torque oil pan bolts?
Engine oil pan bolts range in torque from seven foot-pounds to 22 ft-lb or more for large engines with heavier pans and bolts. Once you've torqued the bolts and filled the engine with oil, you should run the engine for five minutes to bring it up to normal operating temperature.

Videos and more info

https://www.google.com/search?q=2012+chevy+equinox+oil+pan+bolts+torque

..

2001 Monte Carlo Oil Pan Gasket Replace Info

Only a trusted local auto service shop or dealer can answer this for you because your vehicle would have to be up on a lift to actually see what's leaking in order to properly diagnose and repair. It may be as simple as changing the oil pan gasket or a cracked oil pan that would have to be either replaced or repaired depending on the size of the crack. There is also the remote chance that its actually something else that's leaking. Hope this helps.

I would advise getting a second opinion A mechanic told me my 92 Le sabre 's tranny was shot and when I took it to another mechanic he found my spark plug wires were shorting out and causing the car to down shift when you went up a slight incline and it would jump in and out of different gears. I replaced the plugs and wires myself and it rau like new.

by the oil filter itself there is a oil sealer i suppose that should be the problem

Most transmission pans do not have a drain plug. To drain the transmission the velicle will have to be raised. I usually set a large drain pan-several quarts in size-under a rear corner of the transmission pan. I loosen about three bolts on the corner so the transmission fluid will drain. When drained, I remove the rest of the bolts-all 32 or more of them. With the pan off check the color of the fluid look for burnt looking fluid. See if the fluid smells burnt. If so you may have other transmission problems. Look for metal pieces in the transmission pan another indicator of other problems. Clean all the old gasket from the pan and transmission housing-be careful not to gouge either the pan or housing. I use my finger or thumbnail if possible. Gouging either of these places will cause leaks. If you're going to replace the screen do so now. Place the new pan gasket on the pan. Check with the manufacturer's specs before using any permatex or other silicones to hold the pan gasket. I always slide a bolt or two through the pan and gasket holes, lift the pan, and start the bolts. Go slow. Make sure each bolt is going through the gasket hole before tightening it to the transmission housing. Replace the bolts and tighten to a snug using a criss-cross pattern. Go back and forth across the pan tightening each bolt a few turns until all are tight. Don't overtighten the bolts. Doing so will damage the pan gasket, When all bolts are tight, refill the transmisson slowly checking for leaks. Fill the transmission to manufacturer's specifications.

There is a gasket between the engine and the oil pan. It is probably stuck. You will have to pry it loose with a screwdriver. It may damage the gasket so you might have to get a new one. Make sure you scrape off the old gasket before installing the new one.

Just Check The Drain Plug , Then Drain the Old Oil, Before Filling It With New Oil Check The Oil Quantity From Your Manual Book .And Add Same Amount Of Oil. Thanks.

drop tranny pan.which will drain fluid. replace filter, gasket then pan refill with fluid .start and let run a few minutes then put in gear it may take a second for fluid to get all thru trans that should do it

Hi to reset the oil life monitor
turn the key on engine off
push the gas pedal to the floor 3 TIMES WITH IN 5 SECONDS
the light will flash then go out