2010 dodge caravan minimum rotor thickness

Hello there
From a kind chap on this page
http://buickforums.com/forums/threads/18395-Service-limits-for-brake-rotors

For a 2000 Buick LeSabre

FRONT BRAKE ROTORS:
Discard Thickness30.7 mm (1.209 in.)
Lateral Runout (New)0.06 mm (0.002 in.)
Minimum Thickness after Refinish31.08 mm (1.224 in.)
Rotor Diameter 15 inch Wheels (New)278.0 mm (10.9 in.)
Rotor Diameter 16 inch Wheels (New)303.0 mm (11.9 in.)
Rotor Thickness (New)32.20 mm (1.267 in.)
Thickness Variation (New)0.025 mm (0.001 in.)

I don't know the min thickness, but I have an outback just like yours and if there is a problem with uneven rotors it's usually cheaper and easier to buy aftermarket at NAPA auto or other supplier (shop around) and trash the old rotors. If the rotors can be turned then keep them for the next brake job and use them then. Outbacks are easy to do about 30 min a side rotor and pads after the wheel is off, just did mine.

IT IS INBOSSED ON ROTOR IF YOU LOOK FOR IT

Rear Brakes JC5/JH5 Utility Only
Rotor Discard Thickness* .............................. 28.50 mm (1.122 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 29.0 mm (1.142 inch)
Rotor Thickness-new .................................... 30.0 mm (1.181 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

Rear Brakes JH6
Rotor Discard Thickness * ............................. 27.50 mm (1.082 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 28.0 mm (1.102 inch)
Rotor Thickness-new .................................... 29.0 mm (1.141 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

Yup! Warped rotors will cause that - and if severe enough, may be felt as a pulsating brake pedal under your foot when you're applying the brakes.
Many auto supply shops used to offer "turning" of rotors and drums on a lathe while your waited for a few bucks each. The thickness of many newer auto's drums and rotor is so small that there's seldom enough metal to have them "turned" and still meet the minimum required thickness. That means buying new drums or rotors instead.

In this tutorial, we learn how to check the brake pads on a 2008 Dodge Caravan, check the thickness of the brake pads on the car to see if they are thick enough. The rear pad is surrounded by a gold piece called the "shoe" and the rotor. The front pad has to be inspected by laying on your back and looking for the pad to see how thick it is. If the thickness is not enough, you need to replace it as soon as possible. Make sure the brake pads are up to t

Minimum thickness is 27.9mm or 1.09"...... I dont know what "run off limit" means? It doesnt matter, the minimum is the minimum, period.

Its minimum thickness must be 22mm but the specified size is 25.4mm which would fit in perfectly

if you have to ask that question you should replace them

there is many kind of brake system of ur truck here i will send u everything about the brake and i hope its help

Rear Brakes JC3

Rotor Discard Thickness* 18.50 mm/0.728 in Rotor Minimum Allowable Thickness After Refinish 19.0 mm/0.748 in Rotor Thickness (new) 20.0 mm/0.787 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JC4

Rotor Discard Thickness* 28.50 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring1 .50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH2

Rotor Discard Thickness* 28.50 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH6

Rotor Discard Thickness* 27.50 mm/1.082 in Rotor Minimum Allowable Thickness After Refinish 28.0 mm/1.102 in Rotor Thickness (new) 29.0 mm/1.141 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH7

Rotor Discard Thickness* 28.5 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this Specification. After refinishing the rotor, replace any rotor that does not meet the minimum or discard thickness specifications.