Disconnect the speaker electrical connector and remove the door speaker (if equipped).
Detach the door latch release handle.
CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. Detach the watershield.
Using a suitable plastic knife (disposable cutlery), cut through the Butyl strip to enable the watershield to be peeled back.
Remove the door glass top run retainer.
Vehicles with manual windows
Install the window regulator handle.
Vehicles with power windows
Connect the door glass operating switch electrical connector.
All Vehicles
Align the regulator clamp with the access hole (power window shown).
NOTE: Position the regulator operating cable to one side when drilling the retaining pin, in order to prevent damage. Detach the door glass from the regulator clamp.
Using a suitable electric hand drill and a drill bit 8 mm, remove the retaining pin.
Push out the retaining sleeve.
Remove the door glass from the regulator clamp.
Discard the retaining sleeve.
Support the glass, lower the glass and regulator to the lowest position.
Position the lower part of the door glass top run outside the door.
NOTE: To aid removal of the door glass, stand on the inner side of the door. Make sure the glass is removed from the inside of the door. Remove the window glass.
Installation All vehicles
CAUTION: Make sure vise jaw protectors are used. NOTE: Make sure that the retaining sleeve is central in the door glass. Attach a new retaining sleeve and retaining pin to the door glass.
Position the retaining sleeve in the door glass.
Using a suitable vise, press the retaining pin into the retaining sleeve.
Install the window glass in the door.
Attach the door glass to the regulator clamp.
Push the door glass firmly down to engage the retaining pin and retaining sleeve into the regulator clamp.
Position the lower part of the door glass top run on the inside of the door.
Close the window.
Install the door glass top run retainer.
Attach the watershield.
Attach the door latch release handle.
Connect the door speaker electrical connector (if equipped).
Install the door speaker (if equipped).
Install the side impact bolster.
Vehicles with manual windows
Remove the window regulator handle.
Vehicles with power windows
Disconnect the door glass operating switch electrical connector.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Remove the door panel. Look for screws around the edge and at the arm rest and handle. After there out pop the panel off, pry at the bottom first and work your way around. Then you'll have access to the window regulator and glass. remove the trim at the bottom of the window opening to remove or install the glass.
Remove the door panel, remove the window trim, remove the window regulator, Remove the window frame(push down ,then pull out from the top), Remove the broken glass from the seal, install window. Put back together in reverse order. You will need a Phillips screw driver, a drill and 1/4 bit, a 10 MM wrench or socket, 1/4 rivets X 1/2 inch long and rivet gun that handles up to 1/4 inch rivets.
remove the door trim to get to in side the door. One of the glass tracks will have an adjustment on the lower mount where you can move the track in or out depending what you want. Normally wind the window right down and adjust the track tight against the glass( make sure the glass is in straight). wind the glass up and down a few times to ensure that there are no tight spots Some spray silicon in the tracks helps with the movement of the glass.
If the motor is working but the glass is not moving something must have broke inside the door. See if you can sneak a piece of duct tape down along side the glass, get it down as far as possible. Use a butter knife or something to make the tape stick to the glass, now try pulling the glass up with the tape. You may want run the window motor at the same time maybe it will catch. If you get the window up, tape it with duct tape so you can get it to a shop to get it fixed. Good luck.
Remove door trim panel and watershield. Refer to Section 01-05.
CAUTION: Prior to removing center pins from the rivet, it is recommended that a suitable block support be inserted between door outer panel and glass bracket to stabilize glass during rivet removal. Remove center pin from each rivet with a drift punch. Using a 1/4-inch diameter drill, drill out remaining rivets as damage to plastic glass retainer and spacer could result.
Remove two rivets attaching glass to run and bracket assembly.
Remove glass.
Remove drillings and pins from bottom of door.
Installation
Snap plastic retainer and spacer into two glass retainer holes. Make certain that metal washer in the retainer assembly is on outboard side of glass.
Insert glass into door.
Position glass to glass bracket. Install two rivets to secure glass to glass bracket.
NOTE: Two 1/4-inch-20 x 1-inch bolts and two 1/4-inch-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (36-61 lb-in). Equivalent metric retainers (6mm) may be used.
Install door trim panel and watershield. Refer to Section 01-05.
Remove the rear door trim panel. For additional information, refer to Section 501-05 .
Remove the watershield.
Remove the interior weatherstrip.
Remove the exterior-weatherstrip.
Remove the nut and the rear window stabilizer.
CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass. NOTE: Lower the window to access the rivets. Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.
Disconnect the speaker electrical connector and remove the door speaker (if equipped).
Detach the door latch release handle.
CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. Detach the watershield.
Using a suitable plastic knife (disposable cutlery), cut through the Butyl strip to enable the watershield to be peeled back.
Remove the door glass top run retainer.
Vehicles with manual windows
Install the window regulator handle.
Vehicles with power windows
Connect the door glass operating switch electrical connector.
All Vehicles
Align the regulator clamp with the access hole (power window shown).
NOTE: Position the regulator operating cable to one side when drilling the retaining pin, in order to prevent damage. Detach the door glass from the regulator clamp.
Using a suitable electric hand drill and a drill bit 8 mm, remove the retaining pin.
Push out the retaining sleeve.
Remove the door glass from the regulator clamp.
Discard the retaining sleeve.
Support the glass, lower the glass and regulator to the lowest position.
Position the lower part of the door glass top run outside the door.
NOTE: To aid removal of the door glass, stand on the inner side of the door. Make sure the glass is removed from the inside of the door. Remove the window glass.
Installation All vehicles
CAUTION: Make sure vise jaw protectors are used. NOTE: Make sure that the retaining sleeve is central in the door glass. Attach a new retaining sleeve and retaining pin to the door glass.
Position the retaining sleeve in the door glass.
Using a suitable vise, press the retaining pin into the retaining sleeve.
Install the window glass in the door.
Attach the door glass to the regulator clamp.
Push the door glass firmly down to engage the retaining pin and retaining sleeve into the regulator clamp.
Position the lower part of the door glass top run on the inside of the door.
Close the window.
Install the door glass top run retainer.
Attach the watershield.
Attach the door latch release handle.
Connect the door speaker electrical connector (if equipped).
Install the door speaker (if equipped).
Install the side impact bolster.
Vehicles with manual windows
Remove the window regulator handle.
Vehicles with power windows
Disconnect the door glass operating switch electrical connector.
This is a professional job for a conv. top shop. has to be sewn in at the bottom.
Removal NOTE: Mark vinyl to be removed so it can be returned to the same position after disassembly.
Remove sail area panels as outlined.
Remove staples retaining elastic straps at each side of back window glass (42006) to rear tacking strip and folding top rear number 4 bow (51278) and remove elastic straps.
Remove staples retaining rear bow corner pad (537A71) and bottom of folding top back window curtain (52500) to rear tacking strips.
Remove staples retaining top of folding top back window curtain to folding top rear number 4 bow and remove back window glass .
1994 mustang. don't have 89
Window, Rear
Installation NOTE: Transfer markings from the removed assembly.
Mark with grease pencil center point on folding top rear number 4 bow in line with hole on rear of folding top rear number 4 bow .
×