How do i program a third honda pilot ket from two masters

Based on my research, that Valet key has to be programmed by a dealership. There is a chip in that key that is not being recognized by the car. Your other key is programmed to be recognized by the car. there is a way to reprogram the keyless entry fobs, but not this Valet Key. call around because dealerships may vary wildly on cost. I once had one programmed for free. Good luck.

When the correct number of learned master keys are not available to perform adding keys procedure the 10 minute re-learn procedure or 30 minute re-learn procedure must be performed. Refer to Programming Theft Deterrent System Components .
30-Minute Relearn Procedure
Use this procedure after replacing any of the following components:
?€¢
The PASS-Key III plus keys

?€¢
The theft deterrent module (TDM)

?€¢
The powertrain control module (PCM)

Important:
?€¢
This procedure is not available on vehicles equipped with EXPORT configured TDMs.

?€¢
When performing the 30-minute relearn procedure, all previously learned keys will be erased from the TDM memory. Additional keys may be learned after performing the relearn procedure.

?€¢
When replacing a TDM with a GM SPO Replacement Part, ensure the procedure to setup a new TDM is performed prior to the 30-Minute Relearn Procedure.

1. With a master vehicle key, turn ON the ignition, with the engine OFF.
2. Observe the security indicator. After approximately 10 minutes, the telltale will turn OFF.
3. Turn OFF the ignition, and wait 5 seconds.
4. Repeat steps 1-3 two more times for a total of 3 cycles or 30 minutes.
Important: The vehicle learns the key transponder information and/or passwords on the ignition switch transition from OFF to RUN. You must turn the ignition OFF before attempting to start the vehicle.

5. With a master vehicle key, start the vehicle. The vehicle has now learned the key transponder information and/or the ECM has now learned the fuel continue password.
6. If additional keys are required to be learned, refer to Adding Keys .
7. With a scan tool, clear any DTCs.

Adding Keys
Important:
?€¢
To initiate, this procedure requires that a learned master key be available.

?€¢
A total of 10 master keys or valet keys may be programmed to a single vehicle.

?€¢
This procedure adds keys only. The procedure does not erase previously learned keys.

?€¢
The keys to be learned must duplicate the mechanical cut of the current key.

?€¢
If more than one valet key is to be learned, immediately precede each valet key with a learned master key.

1. With a previously learned master key, turn ON the ignition, with the engine OFF.
2. Turn OFF the ignition and remove the key.
3. Within 10 seconds insert the key to be learned. Turn ON the ignition with the engine OFF. The vehicle has now learned the new key.

all back seats are either screwed down or hooked in. you need to use a little muscle and lift up your back seat to see which is which. there is no other way to gain entry to your trunk.Trust me Ive locked my keys in my trunk too. Now i have a hidden spare to my door and trunk. GOOD LUCK

I believe that this is to protect valuables left in the boot when parking the vehicle. I read here that there is access some where in/ near the glove box but I cannot remember exactly what it was . Surf the net under Jaguar valet problems and you may get the answer.

Use the master key, not the valet. The valet key is gray and will only unlock the drivers door and start the vehicle. If you don't have a master key, have one cut at the dealership, but you will need to have the immobilizer chip programmed into the vehicles computer $$$ cost is around $100 for the key and programming. Simple Car Answers Your Most Reliable Source for Automotive Repair...

Hello and welcome. this is how you learn a new key. please note this is for adding a new key. you must still have one working key for this to work.

Adding Keys Important: • To initiate, this procedures requires that a learned master key be available. • A total of 10 keys may be programmed to a single vehicle. • This procedure adds keys only. The procedure does not erase previously learned keys. • The keys to be learned must duplicate the mechanical cut of the current key. • If more than one valet key is to be learned, immediately precede each valet key with a learned master key.

1. With a previously learned master key, turn ON the ignition, with the engine OFF.
2. Turn OFF the ignition and remove the key.
3. Within 10 seconds of turning OFF the ignition, insert the key to be learned and turn ON the ignition. The vehicle has now learned the new key.

Your vehicle comes with two kinds of keys: a master key and a valet key.
The master key fits all the locks on your car:
Ignition
Doors
Trunk
Trunk release handle
Rear seat trunk access

The valet key works only in the ignition and the door locks. You can keep the trunk, trunk release handle and rear seat trunk access locked when you leave your car and valet key at a parking facility.

You should have received a key number plate with your set of keys. You will need this key number if you ever have to get a lost key replaced. Keep the plate stored in a safe place.

When replacing keys, use only Honda-approved key blanks.

There are many hardware stores that have Honda key blanks and can make a key if you have a working one. If not, a Honda dealership can get you a key (expensive) for your vehicle if what is left of your key has the small serial number still on it. Additionally, they might be able to get one based on the VIN number of your car.

Hope this helps you.

I have seen this before, each time i have seen it i have to reprogram the valet key. This needs to be dont at the dealership, make sure you bring the master key otherwise they cant program the valet key.

Use vin number and have one mailed.

Hi, I read your comment,
The key for you Honda Accord use chip ,
If you need an master key or extra key you can go to Honda dealer bacause need to be programed by a tech with computer.

But you have the option to Lock smith lots of them can do if they have the computer to programing and is more cheap than dealer.

I hop this information is good for you.