How do i set radio stations

Tune into 102.0 then hold button "1" for a few seconds (you may hear a beep as it registers). Tune into 98.0 and then hold button "2" for a few seconds. Tune into the next station and then hold "3" and so on. Now when you press "1" it will go to 102.0 "2" will go to its' preset and so on.

that is normal. if you want use the seek or scan buttons.

When tuned into a station, press and hold the number that you want to assign to that station.

AM / FM RADIO
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations (six AM,
six FMI and six FM2) by performing the following
steps:
1. Turn the radio on.
2. Press AM FM to select AM, FMI or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever you press that numbered pushbutton, the station you set will return.
5. Repeat the steps for each pushbutton.


RADIO WITH CD ( BASE LEVEL)
Setting Preset Stations
The six numbered pushbuttons let you return to your favorite stations. You can set up to 18 stations (six AM, six FMI and six FM2) by performing the following steps:
1. Turn the radio on.
2. Press AM FM to select AM, FM1 or FM2
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever you press that numbered pushbutton, the station you set will return.
5. Repeat the steps for each pushbutton.


RADIO WITH CD (UP LEVEL)
Setting Preset Stations
The six numbered pushbuttons let you return to your favorite stations. You can set up to 30 stations (six AM, six FMI and six FM2, six XM1 and six XM2 (USA only, if equipped), by performing the following steps:
1. Turn the radio on.
2. Press BAND to select AM, FMl, FM2, or XMI, or
3. Tune in the desired station.
4. Press EQ to select the equalization.
5. Press and hold one of the six numbered XM2. pushbuttons until you hear a beep. Whenever you press that numbered pushbutton, the station you set will return and the equalization that you selected will also be automatically selected for that pushbutton.
6. Repeat the steps for each pushbutton.


Additional details could find in your Owners Manual; hope this helps (remember to rate this answer)

Im not sure what countyr you are from....but you may have to buy a radio converter.......

if you have a factory radio, then chance are you antenna is amplified (even if you don't have an antenna that goes up in the back). The fuse for the antenna amplifier could have blown or the amplifier itself my have gone bad. It could also be your radio but, i would check those things first... Just a side note: i don't know of any stations that around me that aren't odd numbers 92.3 fm,95.5 fm,100.3 fm. Where you able to tune it to 100 fm before?

factory radios only tune into odd numbers... radios stations broadcast on odd numbers to avoid some frequency interference... ive only see a few aftermarket radios that tune to even numbers also

You have a failed output section inside the radio. If you remove the radio, and take it apart, you will see some burnt capacitors at the very back side of the PC board. This is, unfortunatly, a very common problem with those cars. You are going to have to get another radio, the expense for the manufacturer to fix is is more expense than a replacement. Sorry, but I have seen this situation too many times.

Why? North American radio stations are only broadcast on "odd" frequencies - x.1, x.3, etc.

Try just holding the button of choice down. In my Audi, when I had a factory head unit, to set for example, preset 2, I'd just tune to the station I wanted to program, and then hold down the number 2 preset button until the display stopped blinking. It was then preset.