Question about 2002 Ford Crown Victoria

1 Answer

Hw to put on a serpintine belt on a 2002 crown vic

How to put a serpintine belt on

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Ford Master
  • 615 Answers

There is a hole in the tensioner that you can put a ratchet in and take the tension off of the belt ,You can than easily replace the belt

Posted on Nov 20, 2015

Ad

5 Suggested Answers

dlongav

David Quesenberry

  • 98 Answers

SOURCE: radio does not work in 1993 crown vic, want to put in a replaceme

Go to your local auto parts store where you can purchase a Ford audio removal tool. It looks like a wire shaped "U" that is inserted in the holes on face of audio system ..Follow the directions for use , you will find it a pretty easy task with the correct tool..

Posted on Dec 28, 2008

Ad

Ted Schore

  • 7353 Answers

SOURCE: how do i install a fan belt on a 93 crown vic

I think DAYCO has belt routing diagrams.

Posted on Sep 24, 2009

Anonymous

  • 76 Answers

SOURCE: cant start my crown vic 1998

ignition switch or starter relay or a wiring problem

Posted on Oct 03, 2009

Testimonial: "knows what he is talking about"

Anonymous

  • 65 Answers

SOURCE: 2000 crown vic police interceptor bypass a/c clutch pulley

you can get a A/C Delete kit for a Ford 4.6 liter. the 4.6 v-8 accessory drive system is all the same. You may also be able to run a line of string around the pullys, take it to your local auto parts store and they can match it up. I recomend the kit,

Posted on Oct 06, 2009

ftw1952

frank thomas wilson

  • 10319 Answers

SOURCE: 2002 ford crown vic. driver side wiper not

the linkage between the wiper motor and the wiper arms needs to be replaced. the stud on the one side is stripped and that is why it doesn't work as it should. this happens usually when the wipers are left on in the winter with the blades freezing to the windsheild. turn on the car with frozen blades tends to strip out the teeth holding the wiper arms onto the linkage

Posted on Jun 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a stater on a 2002 crown vic. from the ground


You must jack up ,or put on a lift to reach the starter ,if you jack the car up be sure to put jack stands under the frame before you get under it .(safety first always.)the starter is on the passenger side, bottom of the engine. if this was helpful please leave good feed back

Mar 02, 2015 | 2002 Ford Crown Victoria

1 Answer

Replace serpintine belts on 2002 mazda millenia 2.5l


is it the one belt or does it have the 3 belts

Dec 28, 2012 | 2002 Mazda Millenia

1 Answer

My 2002 crown vic started backfireing then would not start seems to not be getting any gas could this be my coil pack?


It sounds more like a timing belt has failed.
check for spark at the spark plugs
If there is no spark you can have the coils tested
But i till think timing belt due to the back fire and then the no run
If this was helpful please rate this question

Jan 24, 2011 | 2001 Ford Crown Victoria

1 Answer

Hello .. i have a problem with my car '' sounds under the hood '' my car is a 2003 ford crown victoria i hear sounds under the hood , i notice these sounds as long as the car is running either...


open the hood listen to where the noise is comming from I suspect pullys shut off engine .Get a full can of wd40 spray one pully at a time start engine after spraying each pully when the noise quites down or goes away that will be the pully you will want to inspect further or replace before it leaves you stranded. I drive a 04 crown vic great car ps while your there check your serpintine belt. shouldnt be cracked or missing teeth. about 30 dollars at napa easy to replace.

Nov 21, 2010 | Ford Crown Victoria Cars & Trucks

1 Answer

Serpintine belt diagram for 1986 ford crown vic


There "should" be a black sticker with white diagrams on it. This is generaly located on the upper radiator support or sometimes near to the heater hoses entering the firewall. The sticker is about 1 1/2 inches square. If it is not there or worn out, most dealerships will gladly give you a printout at the service desk. Thanks, Dana

Feb 28, 2010 | 1986 Ford Crown Victoria

1 Answer

Pulsing feel to right in steering wheel on hard left-hand turns.


What rims are on the car the steel police ones and what tires are on it could be hitting the stops on the frame and where the proper bolts put back in on the rack mounts and did you go with the heavy rack for the police car .Cause when I built them there was an issue with the proper bolts and there was a different rack for the cop cars the to the basic crown vic do to the suspension upgrade on it and the diffrent pump

Mar 12, 2009 | 2003 Ford Crown Victoria

1 Answer

Put fan belt back on


sould be a diagram of the belt routing on the fan shroud.Easy to get it wrong.

Dec 13, 2008 | 1994 Ford Crown Victoria

1 Answer

2002 crown vic


you need to jack that side of the engine up. take the right side motor mount bolt loose then jack the engine up from underneath. be sure to use a block of wood or somthing so you dont bust the oil pan

Jul 22, 2008 | 2002 Ford Crown Victoria

Not finding what you are looking for?
2002 Ford Crown Victoria Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...