Question about Cars & Trucks

1 Answer

98 Honda accord psi on head bolts - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 24 Answers

Torque the head bolt to 22ft. lbs. then an additional 180 degrees ( if using new head bolts 270 degrees ) in sequence.

Posted on Sep 04, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

six-of-ten

  • 208 Answers

SOURCE: 98 Honda Accord

Welcome to the intermittant fault main relay club. Check the other posts (also Civic) for this problem on this website and http://autorepair.about.com Your problem is common and complicated. Good Luck.

Posted on Aug 09, 2008

Anonymous

  • 1 Answer

SOURCE: 2005 honda accord / head light

I believe there is a panel in the wheel well that gives you access to the headlight....

Posted on Mar 17, 2009

Anonymous

  • 12 Answers

SOURCE: head bolt torque specs for 200 honda accord 3.0

its a three step process 1st 29ft/lbs 2nd 51ft/lbs 3rd 72.3ft/lbs

Posted on Apr 25, 2010

samtoler

Sam Toler

  • 666 Answers

SOURCE: head bolt specs for a 91 honda accord 2.2l

Tighten the bolts in a pattern as such; 8 6 2 4 10
9 3 1 5 7 So if you were looking straight down onto the head, the first bolt you'd tighten would be the center one, closest to you. The second bolt you'd tighten is the center one farthest from you. The 3rd would be one left for middle closest to you, 4th would be one right from center, farther from you...Make sence? Tighten them all in that sequence, to 29 ft-lbs. After they are all tightened in that order, start from 1 and tighten them all to 51ft-lbs. Then finally, tighten them all down to 72ft-lbs. Make sure to follow that order every time. If a bolt makes a wierd noise while you are tightening it, loosen the bolt, and retorque it from the 1st step.

Posted on Jun 12, 2010

Jerry Van Sickle

  • 334 Answers

SOURCE: torque specs for head bolts

Hello joee105,

The head bolt torque is a three step procedure:

1. 29 ft. lbs.
2. 51 ft. lbs.
3. 78 ft. lbs.

See image below for torque sequence.

netvan_192.png

I hope this helps.

Regards,

Jerry

Posted on Aug 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the head bolt torque sequence for a 1996 honda accord 2.2? I also need to know the pounds of pressure and how many passes needed to torque. Thanks


Install the cylinder, then tighten the cylinder head bolts sequentially in 3 steps. step 1. 29 ft. lbs. step 2. 51 ft. lbs. step 3. 72 ft. lbs.

Sep 06, 2012 | 1996 Honda Accord

1 Answer

My have a blown head gasket on my 2000 Honda Accord V6. What could have led to this problem?


most common causes of blown head gaskets are engine overheating. could be caused radiator cooling fans inoperative, cooling system leaks, clogged radiator passages,or sticking thermostat. if a head gasket is severely blown the cooling system will pressurize very rapidly on cold engine startup. other more rare cases of head gaskets blowing could be loose head bolts. make sure new head bolts are used and torqued correctly if service manuals recommend new head bolts.

Jul 14, 2012 | 2000 Honda Accord

1 Answer

98 honda accord v6 only has 90 psi compression


90 psi compression is the minumun for gas engine to ignite, you have low compression what is the compression next to it? The compression on Honda V6 is 200psi. you can have a valve problem a blown head gasket, Also make sure your compression gauge is accurate by using another compression gauge

Mar 23, 2012 | 1998 Honda Accord

1 Answer

Torque specs for head bolts on a 2000 2.3 honda accord


how mach tayp 2000 hona accord head bolt specs

Jan 29, 2012 | 1993 Honda Accord

1 Answer

Torque specs for head bolts on a 99 3.0 honda accord


Hello joee105,

The head bolt torque is a three step procedure:

1. 29 ft. lbs.
2. 51 ft. lbs.
3. 78 ft. lbs.

See image below for torque sequence.

netvan_192.png

I hope this helps.

Regards,

Jerry

Aug 21, 2011 | 1993 Honda Accord

2 Answers

How many psi of freon does your 1995 honda accord lx need


People, he asked for the psi, not how to do it and everything else. High side, 35-50 psi. Low side 20-35 psi. Very simple question to answer. He likely knows how to do it, just needs the psi for high and low.

Mar 02, 2010 | 1992 Honda Accord

2 Answers

Head bolt torque specs for 200 honda accord 3.0


its a three step process 1st 29ft/lbs 2nd 51ft/lbs 3rd 72.3ft/lbs

Oct 08, 2009 | 1993 Honda Accord

1 Answer

Need to remove bumper of 2000 Honda Accord Coupe


i think there just bulbs unless u have damage and your replacing .i have a 98 also owned 92,94 i just started removing bolts attached to bumper but putting on a little tougher start one top center bolt then do the one on each sidein wheel wells to fit it in there ask someone to help hold while your bolting then do rest of bolts wamo bamo....

Mar 14, 2009 | 1998 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...