Uplander wiring diagram

thats an optional equipment wiring harness. if you dont have heated mirrors or power mirrors and the mirror still fits, install it.

The rain sensor is located at the inside rear view mirror.

Temperature Display
The inside rearview mirror supplies a 5 volt signal circuit and low reference circuit to the ambient air temperature sensor. The inside rearview mirror monitors and records the voltage on the signal circuit of the ambient air temperature sensor. The inside rearview mirror uses this recorded voltage to display the temperature on the temperature display portion of the compass/temperature display. The temperature display will show "ICE" when the ignition is first turned on and the current temperature is 3°C (37°F) or below. The display will toggle between "ICE" and the actual outside temperature for approximately 4 minutes.
The mirror will display "OC" if the mirror senses a temperature of less than -40°C (-40°F).
the mirror will display a "SC" if the mirror senses a temperature of greater than 112°C (143°F).



Replace the inside rearview mirror with compass. Refer to Inside Rearview Mirror Replacement .

Hello, to replace the rear mirror, try the following:

1. Roll the passenger side door window all the way down. Turn off the ignition and remove the keys.


2. Gently pry the window control panel from the arm rest with the pry tool or screwdriver starting at the bottom of the panel. Flip it over and unplug all the wire harness outlets from it. Set the panel aside.

3. Locate and remove the two panel door plugs near the arm rest concealing the two screws and remove the screws with the Phillips head screwdriver.

4. Remove the door panel retainer plugs along the edge of the door by pressing in the middle of the plug to unlock it and removing the plug.


5. Detach the mounting triangle from the upper inside door panel covering the side-view mirror.

6. Remove the door panel by lifting outward and then upward. Disconnect the speaker wire harness from the underside of the door panel and set the door panel aside.

7. Locate and disconnect the mirror wire harness.

8. Pull back the foam insulation from the inside panel covering the side-view mirror.

9. Unscrew the three mounting nuts from the mirror using the ratchet, extension and a socket. Do not drop the nuts into the door cavity.

10. Pry the mirror gently away from the outside of the door.

11. Install the new mirror and replace the mounting nuts on the mirror studs and tighten with the ratchet, socket, and extension. Plug the mirror wire harness back in. Replace the foam insulation. Replace the mounting triangle.


12. Replace the door panel by reversing the procedure. Start by plugging in the speaker wire first.


Thanks

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

There is a triangular piece of plastic inside the door opposite the mirror. You remove the panel and you'll see 2 bolts. Remove the bolts and unplug the wire connector (if you have electric rear view mirrors) and the mirror will come right off. Installation is reverse.

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

Mirror — Outside Rear View Removal
NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.

1. Disconnect the battery ground cable (14301).

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

Installation

1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
   To install, reverse the removal procedure.

Running wires from external sensors is going to be a difficult job because you have to drop the headliner and the left A post cover for access to the wires. There are manuals available at auto parts stores that have diagrams, but you need to be sure that it covers the wiring for the new mirror.

Hiya...ALL factory-installed rearview mirrors are installed with different wires due to options.
About 6 different rearview mirrors are installed with those options such as On-Star, light, compass, and those features which use different wires....THIS CANNOT be modified with different rearview mirror....**for example, the Equinox owner attempt to pull out a factory-installed base rearview mirror and put in different one that has compass/temperature built into the rearview mirror**

However, the wires are located inside the front headliner which requires removing the sunvisor (and possible removal of interior plastic trim part at the left/right ends of the windshield) prior to pull the headliner down, and a small metal philips or torx screw is used to secure the rearview mirror onto the bracket glued to the windshield.

The best solution is to leave the original factory-installed rearview mirror in place.