04 navara pickup noisy rear axle does not seem to be wheel bearings 130000 miles

Some tires are noisy.
Some rear axle HD differentials make noise.
Differential bearings may be noisy.
When the differential was drained, the oil should have been inspected for metal residuals.

replacing bearing involves removing axle your not replacing a hub but tearing apart axle 99 04 F250 Sterling Rear axle bearing replacement Pt 2 2006 Ford F250 rear hub axle seal replacement F250 Rear Brakes Axle Hub Removal Install 03 07 Powerstroke

Rebuilding them consists of new U joints and maybe balanced. If it was so loose the the u joints wallowed out the keepers, Then yes, they would also need replaced. Cut off and welded on. That isn't a common problem, but I have had to replace a few. Not just on jeeps.

If you have an axle bearing problem then remove that axle but if you have a bearing in the diff itself then the crown wheel and pinion have to come out after you have pulled the axles. If you have no experience with diffs then get a transmission specialist to do it or you will damage the diff at worst or have a noisy diff at best which will eventually destroy the diff.

YOU WILL HAVE TO REMOVE THE AXLE WITH THE WORN BEARING AND PRESS IT OUTAND PRESS IN THE REPLACEMENT

what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) Axle Seal Replacer
T83T-1175-A Axle Wheel Bearing Puller
T83T-1225-A Axle Wheel Bearing Replacer
T83T-1225-B Driver Handle
T80T-4000-W Impact Slide Hammer
T50T-100-A
Removal

1. Remove the axle shaft; refer to Axle Shaft in this section.

Axle Shaft Removal

1. CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
   Loosen the lug nuts (1012).
   1. Remove the center cap.
   1. With the weight of the vehicle on the wheels, loosen the lug nuts.

1. Raise and support the vehicle.

1. Remove the wheel and tire assembly.
   1. Remove the lug nuts.
   1. Remove the wheel and tire assembly.

1. Remove the axle housing cover (4033).
   1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
   1. Remove the axle housing cover bolts.
   1. Remove the axle housing cover.

1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .

1. CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
   Remove the differential pinion shaft.
   1. Remove the differential pinion shaft lock bolt.
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
   Remove the U-washers (4N237).
   1. Push the axle shafts inboard.
   1. Remove the U-washers.

1. Reinstall the differential pinion shaft.
   1. Install the differential pinion shaft.
   1. Install the differential pinion shaft lock bolt finger-tight.

1. CAUTION: Do not damage the inner wheel bearing oil seal (1177).
   Remove the two axle shafts.

Installation

1. Lubricate the lip of the inner wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
   Remove the differential pinion shaft.
   1. Remove the differential pinion shaft lock bolt.
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the inner wheel bearing oil seal.
   Install the two axle shafts.

1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
   Install the U-washers.
   1. Position the two U-washers on the button end of the axle shafts.
   1. Pull the axle shafts outward.

1. Install the differential pinion shaft.
   1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
   1. Install the differential pinion shaft lock bolt.

1. Install the rear disc brake rotors; refer to Section 206-04 .

1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.

1. WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
   Clean the wheel hub and mounting surfaces.

1. Install the tire and wheel assembly.
   1. Position the tire and wheel assembly.
   1. Install the lug nuts and lower the vehicle.
   1. Tighten the lug nuts.
   1. Install the center cap.

1. CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
   NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
   Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.

Installation

1. Lubricate the new rear wheel bearing.
   1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.

1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.

1. Lubricate the lip of the new axle shaft oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.

1. Install the axle shaft; refer to Axle Shaft in this section.

don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal

1. Raise and support the vehicle.
   

1. Remove the wheel and tire assembly.
   

1. Remove the hub grease cap (1131) from the wheel hub.
   

1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
   

1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
   

1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
   
2. Remove the wheel hub from the rear wheel spindle.

OK, have a check on rear axle wheel bearing. Also,
check the propeller shaft bearing, as this also do the
same noise.

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .

1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .

1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.

1. Remove the differential pinion shaft (4211).
   1. Remove the differential pinion shaft lock bolt (4241).
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Remove the U-washer (4N237).
   1. Push the axle shafts (4234) inboard.
   1. Remove the U-washer.

1. CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
   Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. CAUTION: Do not damage the wheel bearing oil seal.
   Remove the axle shaft.

--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal

1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.

1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
   Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.

Installation

1. Lubricate the new rear wheel bearing with the specified lubricant.

1. Using the special tools, install the new rear wheel bearing.

1. Lubricate the lip of the new wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Using the special tools, install the new wheel bearing oil seal.

1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation

1. Lubricate the lip of the wheel bearing oil seal
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. CAUTION: Do not damage the wheel bearing oil seal.
   Install the two axle shafts.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Install the U-washer.
   1. Position the two U-washers on the button end of the axle shaft.
   1. Pull the axle shaft outward.

1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
   Install the differential pinion shaft.
   1. Align the hole in the differential pinion shaft with the case lock bolt hole.
   1. Install a new differential pinion shaft lock bolt.

1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.

1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. Install the rear brakes. For additional information, refer to Section 206-04 .

1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .

1. Lower the vehicle.

Axle Shaft Removal

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .

1. Remove the differential housing cover (4033).
   1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
   1. Remove the bolts.
   1. Remove the differential housing cover.

Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .

1. CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
   Remove the differential pinion shaft.
   1. Remove the differential pinion shaft lock bolt.
   1. Remove the differential pinion shaft.
2. CAUTION: Do not damage the rubber O-ring in the U-washer groove.
3. Remove the U-washer (4N237).
4. Push the axle shaft inboard.
5. Remove the U-washer.

Reinstall the differential pinion shaft.

1. Install the differential pinion shaft.
2. Install the differential pinion shaft lock bolt finger-tight.
3. CAUTION: Do not damage the wheel bearing oil seal (1177).
   Remove the axle shaft.

-----------------------------------------------------------------------------------------------------------------
Seal Removal

1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.

1. CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
   NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
   Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.

Installation

1. Lubricate the new rear wheel bearing.
   • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
   • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.

1. Using the special tools, install the rear wheel bearing.

1. Lubricate the lip of the new wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Using the special tools, install the wheel bearing oil seal.

1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.