Question about 1992 Ford Crown Victoria

Open Question

Camshaft torque specifications - 1992 Ford Crown Victoria

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

squindojr

  • 40 Answers

SOURCE: 2002 escape 3.0 camshaft cap bolt torque

make sure to apply 5w-20 oil to caps prior to install. Also caps and journals are number so you do not install in wrong place. Starting with Righ side looking at pulleys from front, right side cam start with first cap on left being #1 then bolt on other side of cap as #2. Cap behind would be #3 to left then #4 bolt next to it. Keep tightening the next 2 caps behind them in same manner, then jump to front of cam to left side and tighten caps front to back. You should tighten to 10 Nm (89 lbs-in) with a torque wrench. Then you tighten left side head cam caps starting with the left side if looking at front pulleys. Start at front caps working to rear then jump to right side cam front to back. Tighten these caps at 8 nm (71 lb-in) using torque wrench. Also make sure if heads are bolted to block that cam pulley postion is the following: left side looking at pulleys------left pulley mark at 12 o'clock right pulley mark at 3 o'clock. Right side head looking at pulleys------- left side pulley at 9 o'clock and right side pulley at 12 o'clock. When I say clock postion that means using head where valve covers meet as your straight vertical postion.

Posted on Jun 17, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specifications


Head bolts are torqued in 3 steps, 1-18ft.lbs, 2-60 degrees, 3-60 degrees, camshaft caps-10-11 ftlbs, intake manifold-12-17ftlbs, exh manifolds-32-40 ftlbs, camshaft pulley-74-89 ftlbs.

Feb 05, 2014 | Cars & Trucks

1 Answer

2008 forenza 2.0 cam shaft torque specifications


most likely the torque specs are the same as the other model engine that is in your manual just be sure to tighten them slowly and equally back in forth in small increments because those cam shafts can snap very easily

Jan 02, 2013 | 2008 Suzuki Forenza

1 Answer

How do i set camshafts on 1999 duvil northstar


Remove camshaft covrs
Remove front cover
Remove or fully retract all three timing chain tensioners
Remove oil pump
Primary and secondary chain guides should remain in place. Rotate crankshaft until sprocket drive key is at about 1 o'clock position.
Set crankshaft and intermediate shaft sprockets into primary drive chain with their timing marks asjacent to each other.
Install crankshaft and intermediate sprockets over their respective shafts. Rotating crankshaft as necessary to engage crankshaft key in sprocket without changing the timing mark relationship.
Install Flywheel Holder Tool (J-39411) to lock crankshaft in position. Install intermediate shaft sprocket retaining bolt and torque to specifications.
Route secondary chain for left cylinder head over inner row of intermediate shaft teeth.
Route secondary drive chain over chain guide, and install exhaust cam sprocket to chain so camshaft drive pin engages the sprocket notch marked "LE" (Left Exhaust).
There dhould be no slack in the lower section of the chain, and the camshaft drive pin must be perpendicular (90 degrees) to the cylinder head surface.
Install the intake camshaft sprocket into the chain so the sprocket notch marked "LI" (Left Intake) engages camshaft drive pin, while drive pin remains perpendicular to the head face. Minor adjustments can be made to camshaft position to get pin to engage by using a wrench on the hex cast into the camshaft.
Install sprocket retainer bolts and torque to specification.
Repet steps as above to install the right secondary chain to the right camshafts. The right camshaft sprockets are marked "RE" and "RI". In addition, the RE sprocket must contain the camshaft position sensor pickup.

May 27, 2012 | 2000 Cadillac DeVille

1 Answer

Do you have to torque the cam bolts on a 2.4 toyota truck engine?


The specifications call for torquing the camshaft bearing cap bolts to 15 ft. Lbs and the camshaft sprocket bolt to 58 ft lbs. Sometimes experienced mechanics do this by feel.

May 29, 2011 | 1993 Toyota Pickup

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

I need to know how to set thte timing chain


Discoverd this indepth expalaination of process steps involved in the installation of the timing chain from an ASE certified technician. I hope this helps. See the repair manual on the link below.<br /> <br /> Link: <a href="http://www.2carpros.com/forum/2002-jaguar-xj8--gearbox-default-appear-on-dashboard/2000-jaguar-xj8-timing-chain-replacement-vt218070.html">http://www.2carpros.com/forum/2002-jaguar-xj8--gearbox-default-appear-on-dashboard/2000-jaguar-xj8-timing-chain-replacement-vt218070.html</a><br /> <table id="table14" style="BORDER-RIGHT: #000000 1px dashed; BORDER-TOP: #000000 1px dashed; BORDER-LEFT: #000000 1px dashed; BORDER-BOTTOM: #000000 1px dashed" bordercolordark="#000000" width="100%" bordercolorlight="#000000" border="0"> <tbody> <tr> <td style="BORDER-TOP-WIDTH: 1px" width="700"></td></tr> <tr> <td style="BORDER-TOP-WIDTH: 1px" width="700"><span class="name" roundtrip="0" lastvisited="3">By <a name="755408"></a><b roundtrip="0" lastvisited="0">Dave H</b>,<b> </b></span><span class="postdetails" roundtrip="0" lastvisited="0">Certified ASE Technician</span></td></tr> <tr> <td style="BORDER-TOP-WIDTH: 1px" width="100%" roundtrip="0" lastvisited="6"></td></tr> <tr> <td style="BORDER-TOP-WIDTH: 1px" width="700"></td></tr> <tr> <td style="BORDER-LEFT-WIDTH: 1px; BORDER-BOTTOM-WIDTH: 1px; BORDER-RIGHT-WIDTH: 1px"> </td> </tr> <tr> <td colspan="2"> <span class="postbody" roundtrip="0" lastvisited="77">PRIMARY TIMING CHAINS (NON-SUPERCHARGED) <br />NOTE:The 4.0L V8 has no engine timing alignment marks on the crankshaft or camshafts. Engine timing is achieved by installing the Crankshaft Setting Peg (303-531) and Camshaft Locking Tool (303-530). With the crankshaft setting peg in position, ensure the timing flat on each camshaft is in the uppermost position before installing camshaft locking tool. Variable camshaft timing unit may also be referred to as Variable Valve Timing (VVT) unit. <br /><br />NOTE:Special Tools Required: Crankshaft Setting Peg (303-531), Camshaft Locking Tool (303-530), Chain Tensioning Tool (303-532), Primary Chain Wedge (303-533) and Variable Camshaft Timing Oil Control Unit Setting Tool (303-654). See Fig. 232-Fig. 236 . <br /><br />NOTE:"A" bank refers to the right/passenger side of the vehicle and "B" bank refers to left/driver side of the vehicle. <br /><br />NOTE:Each door glass automatically drops 12 mm when the door is opened or when the convertible top is raised or lowered. It is important that windows are lowered before battery is disconnected to allow doors to shut properly. <br /><br />Removal ("A" Bank) <br />Tips Click a link to view tip <br />Tech1Tip: special tool <br /><br /><br />Remove timing cover. See TIMING CHAIN COVER (NON-SUPERCHARGED). <br />Remove the variable camshaft timing oil control solenoid. </span><br /> <span class="postbody" roundtrip="0" lastvisited="77">Remove the variable camshaft timing oil control unit housing retaining bolts and remove the variable camshaft timing oil control unit housing. </span><br /> <span class="postbody" roundtrip="0" lastvisited="77">Remove and discard the variable camshaft timing oil control unit housing "O" rings. <br />Raise and support vehicle. Remove the bolt which secures the Crankshaft Position (CKP) sensor to the flywheel housing. Remove the CKP sensor and allow it to hang free under the engine. Remove the torque converter bolts access grommet from the flywheel housing. </span><br /> <span class="postbody" roundtrip="0" lastvisited="77">Install the crankshaft damper bolt (old one) to the crankshaft, hand-tight only. Rotate crankshaft until the triangular arrow indent on the flywheel is visible through the access hole. See Fig. 144. Confirm that the timing flat on each camshaft is uppermost position. <br />Position the crankshaft so that the Crankshaft Setting Peg (303-531) engages fully into the timing slot. Install and tighten the bolt to secure the crankshaft setting peg. See Fig. 145. Remove the crankshaft damper bolt from the crankshaft and lower the vehicle. <br />Install the Camshaft Locking Tool (303-530) to the "A" bank camshafts, aligning the shafts slightly as necessary. Loosen the bolt that secures the exhaust camshaft sprocket and the bolt that secures the variable camshaft timing oil control unit. See Fig. 146. Remove camshaft locking tool. <br />Remove the primary chain tensioner bolts, primary chain tensioner and tensioner backing plate. See Fig. 147. <br />Remove the primary timing chain tensioner pivot bolt and remove the primary timing chain tensioner blade. See Fig. 148. <br />Remove the bolt which secures the primary timing chain guide. Noting the position of the primary timing chain guide, remove the primary timing chain guide from the upper retaining pin. See Fig. 149. <br />Remove the primary timing chain from the variable camshaft timing oil control unit and from the crankshaft sprocket. Clean and inspect all components. <br />Installation <br />If "B" bank timing chain was removed, see INSTALLATION. If not, go to next step. <br />If previously removed, install the timing chain sprocket to the crankshaft. The teeth of the "A" bank and the "B" bank timing chain sprockets on the crankshaft must be out of phase with each other. If they are in phase after installing, remove the sprocket, turn it on its vertical axis and reinstall sprocket. See Fig. 150. <br />Install the chain tensioning tool to the exhaust camshaft sprocket. Reposition the sprocket (and the variable camshaft timing oil control unit) for the most advantageous position for use of the tool. See Fig. 151. Remove the tool. <br />Install the primary timing chain into position over the crankshaft sprocket and the variable camshaft timing oil control unit. There must be no slack on the drive side of the primary timing chain and the sprockets must not be rotated on the camshafts, or the tensioning tool may not fit. See Fig. 152. <br />Install the primary timing chain tensioner blade to the cylinder block. See Fig. 148. Install the pivot bolt and tighten specification. See TORQUE SPECIFICATIONS. <br />Push the primary timing chain tensioner piston into the tensioner body to provide clearance for installing the primary timing chain. Insert a thin rigid wire through the hole in the end of the tensioner piston to displace the ball from the non-return valve seat. See Fig. 153. With the wire in position, press the piston fully into the tensioner body. Remove the wire. <br />Install the 2 primary timing chain tensioner bolts to the primary timing chain tensioner and locate the tensioner backing-plate on to the 2 bolts. Align and install the primary timing chain tensioner to the cylinder block and to the mating slot on the rear face of the primary timing chain tensioner blade. See Fig. 147. Tighten the primary timing chain tensioner bolts to specification. See TORQUE SPECIFICATIONS. <br />Use a Primary Chain Wedge (303-533), or 2 if needed, between the primary timing chain tensioner and primary timing chain tensioner blade, to take up the slack in the chain for tightening of the variable camshaft timing control unit and exhaust camshaft sprocket. See Fig. 154. <br />Using the chain tensioning tool, apply force to the tool in an counterclockwise direction to tension the chain on its drive side. See Fig. 151. While applying opposing force to the sprocket and chain, tighten the exhaust camshaft sprocket bolt to specification. See TORQUE SPECIFICATIONS. <br />Using the Variable Camshaft Timing Oil Control Unit Setting Tool (303-654), rotate the variable camshaft timing oil control unit fully counterclockwise to the fully retarded position. See Fig. 155. <br />Check that the primary chain wedges are still in place. While applying opposing force to the sprocket and chain using the chain tensioning tool, tighten the variable camshaft timing oil control unit bolt to specification. See TORQUE SPECIFICATIONS. Remove the chain tensioning tool and the primary chain wedges and camshaft locking tool. <br />Raise and support vehicle. Remove crankshaft setting peg. Install the CKP sensor and bolt to the flywheel housing. See Fig. 143. Tighten the CKP sensor bolt to specification. See TORQUE SPECIFICATIONS. Install the access grommet to the housing and lower the vehicle. <br />WARNING:Check that the ring dowels are engaged squarely. Fully locate the assembly as much as possible by hand. Failure to follow this procedure may result in damage to the vehicle. <br /><br />Install NEW "O" rings to the variable camshaft timing oil control unit housing. Lubricate the "O" rings and the bushing. Install the variable camshaft timing oil control unit housing. See Fig. 142. Install the variable camshaft timing oil control unit housing bolts. Tighten to specification. See TORQUE SPECIFICATIONS. <br />Install the variable camshaft timing oil control solenoid. See Fig. 141. Install and tighten the variable camshaft timing oil control solenoid bolt to specification. See TORQUE SPECIFICATIONS. <br />Install the timing chain cover. See TIMING CHAIN COVER (NON-SUPERCHARGED). </span><br /></td></tr></tbody></table>

Aug 26, 2010 | 2001 Jaguar XJ8

1 Answer

2001 vw 1.8 litre gas awv engine spec I am rebuilding my 2001 new beetle engine after the head cracked and I need the engine torque specs. Thanks


Bore × stroke 81.00 mm × 86.40 mm 3.19 in × 3.4 in Cylinders s-4 SOHC Single overhead camshaft DOHC Double overhead camshaft OHV Overhead valves TS Two stroke SV Side valves
  • Sl
  • Sleeve valves
  • oise
  • Overhead inlet side exhaust
  • 5 valves per cylinder
    20 valves in total
    compression ratio
    9.30:1 fuel system
    MPFi Maximum power 150.1 PS (148.0 bhp) (110.4 kW)
    @ 5700 rpm Specific output 83.1 bhp/litre
    1.36 bhp/cu in Maximum torque 210.0 Nm (155 ft·lb) (21.4 kgm)
    @ 1750 rpm bmep 1481.7 kPa (214.9 psi) Specific torque 117.91 Nm/litre

    May 01, 2010 | 2001 Volkswagen Beetle

    1 Answer

    01 mazda protege camshaft torque specs


    CAMSHAFT BEARING CAPS TORQUE TO 125 INCH POUNDS. CAMSHAFT SPROCKETS - 44 FT LBS. YOU NEED A REPAIR MANUAL LIKE A CHILTON WITH CAMSHAFT TORQUE SEQUENCE DIAGRAM. YOU HAVE 20 CAMSHAFT CAP BOLTS THAT HAVE TO BE TORQUE IN SEQUENCE.

    Mar 21, 2010 | Mazda Protege Cars & Trucks

    2 Answers

    Torque specifications cylinders head bolts


    for 1.5/1.6L DOHC, 18 Ft-lbs + 70deg + 70deg + 50deg

    for 1.8/2.0L DOHC, 18Ft-lbs +90deg + 90deg +90deg

    Jun 09, 2009 | 2001 Daewoo Nubira

    1 Answer

    Torque to apply to cylinder head bolts and camshaft bolts


    Autozone.com usually has these specifications.

    Aug 07, 2008 | 1995 Toyota Tercel

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    96 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    Marvin
    Marvin

    Level 3 Expert

    85222 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    gerry bissi

    Level 3 Expert

    4388 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...